Jump to content
SAU Community

Does A Garrett Gtx3076R Need Braided Lines?

Skyline_034

By Skyline_034,
in Engines & Forced Induction

 Share

Recommended Posts

ARTZ Grand Master

ARTZ

Posted
Posted

one water line goes into the block behind the turbo....The other water line goes around the back of the head and into the back of the inlet manifold....its a pain in the ass to get to as there is a couple bolts in the back of the head....you can get with a 10mm spanner but it will try your patience...alot of people just cut it and attach a hose, isn't really the correct way to do it but it can work....make sure you use some heat proof hose though as it cops alot of heat...I used Gates flame proof, i think repco has it.....or wrap it with some kind of heat shielding...or use braided if you can get them..

Skyline_034 Community Regular

Skyline_034

Posted
  • Author
Posted (edited)

The water line goes around the back of the head and into the back of the inlet manifold....its a pain in the ass to get to as there is a couple bolts in the back of the head....you van get with a 10mm spanner but it will try your patience...alot of people just cut it and attach a hose, isn't really the correct way to do it but it can work....make sure you use some heat proof hose though as it cops alot of heat...I used Gates flame proof, i think repco has it.....or wrap it with some kind of heat shielding...or use braided if you can get them..

you reckon you could give me a quick reference to a suitable exhaust manifold (internal)? as ebay has heaps of crap..

as i thought stock would be fine, and i have ordered braided lines as we speak lol.

ill take a look around the head/inlet manifold. pain in the ass to put my arm around there :/ ehhhh

Edited by Skyline_034
ARTZ Grand Master

ARTZ

Posted
Posted

stock manifold will be ok if you want to use it... just wont really handle what the 3076 is capable of...you'd find the 3071 would spool up a little quicker is all and still make plenty of power...but dont stress if you already have the turbo

Skyline_034 Community Regular

Skyline_034

Posted
  • Author
Posted

i found this. When the water line comes around the head, does it go where the green coloured hose is?

7-4-10011-1.jpg

any other pics of where the water line goes? i cant feel it connect to a rubber hose at the back but i cant seem to reach/ feel it from the driver side

discopotato03 Grand Master

discopotato03

Posted
Posted

Yes and that hose is a bastard to get to in situ . It went on my 33 and in the end I had to remove the idle air control valve to get at it .

Nissan did it the right way on RB26s and piped it up to the front of the head on the turbo side and returned it into the top water outlet . Works well because any steam bubbles go out to the top rad tank and out past the cap into the overflow bottle .

A .

Skyline_034 Community Regular

Skyline_034

Posted
  • Author
Posted

Well from what I can see, I can probably get some long nose pliers in there to take off the clip and pull off the rubber hose.

But does the braided line connect straight up or would I have to put a fitting between them? :S

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • TurboTapin
      boost source Size Garrett gt28 gen2

      By TurboTapin · Posted

      You just need to remove the compressor housing, not the entire turbo. I would not be drilling and tapping anything with the housing still on anyways. 
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      So, I put my boat on a boat. First of all, I'm going to come out and say it. Why is Tasmania not considered a holy goal, an apex that all road-legal modified cars go to, to experience? This place is an absolute wonderland of titanic proportions. If people are already getting club runs for once in a lifetime 30 person cruises to Tassy then I've never seemed to see it. It is like someone replaced the entire place with an idyllic wonderland for cars, and all of the people living there with paid actors who are kind, humble, and friendly. Dear god. After doing a lap of almost all of the place I've found that it's a great way to find out all of the little things that the car isn't doing quite right and a great way to figure it all out. All in all, I drove for 4 hours a day for a week and nothing broke. I didn't even need to open the engine bay. This is by all means a great success, but it has left me with a list of things to potentially address. I also now have a 3D printed wheel fitment tool which annoyingly hasn't got any threads in it to actually assemble it. I might be able to tape it together to check the sizing I actually want to use, but it'll likely involving pulling the shocks out to properly measure travel at least at the front, and probably raise the car while I'm at it, at least in the rear. I scraped on quite a few things and I'm not sure how else to go about it. I was taking anything with a bump at what felt like 89 degree angles. And address those 10 other tasks. And wash the car. God damn it is dirty. And somehow, the weather was perfect the entire time - And because I was on the top of Mt Wellington it turns out it was very much about to freeze up there. I did something I typically never do and took some photos up there in what must have been -10 and the foggy felt like suspended ice, rather than mere fog. If you own a car in Australia, you owe it to yourself to do it.
    • QB6SAGR
      Battle of the broken skylines

      By QB6SAGR · Posted

      Damn that was hilarious, and a bit embarrassing for skylines in general 😂 vintage car life ey. That R33 really stomped. Pretty entertaining stuff
    • cosline
      R32 gtr transmission strength, billet plate

      By cosline · Posted

      Hi, I have a r32 gtr transmission. Does any of you guys have an idea how much power it will hold with the billet center plate and stock gearset? At what power level and use did yours brake with or without billet plate? Thanks, Oystein Lovik
    • Rezz
      Spotted on the street....

      By Rezz · Posted

      Saw this replica police car based on a Mitsubishi Starion XX parked next to a 'police box' (it's literally a box) in Hirohata, Himeji City in Hyogo prefecture the other day. It's owned by Morii-san who is a local Mitsubishi Starion enthusiast. According to a local radio station blog post, he always wanted to make a police car himself based on ones he saw in his favourite Manga comics.  As it's illegal to modify a car to look like a police car and drive on the road, Morii-san tried many times to get permission from Aboshi police station headquarters nearby. They refused initially by after they got tired of that they granted him permission. However, the car can only be displayed on private property and obviously can't be registered as long as the police livery is present. The car was completed at a cost of 1.5 million yen (US$ 10,000) in addition to the car cost. A location was chosen outside Hirohata Police box where the car can easily been seen from the street. Morii-san has two other Starion road cars, both widebody GSR-VRs.
×
×
  • Create New...