Jump to content
SAU Community

Recommended Posts

You'll be hard to find an Optus employee who will have access to do this, let alone will do it for you. What are you hoping to achieve by tracing the IP? Do you know if it's a static or dynamic IP, or if the person you're trying to trace is using a VPN?

I can see where this is going.

he has traced an ip and found it an optus net block.

thats as far as you can take it publicly.

guessing this person has attacked/hacked their servers.

I used to manage this process for our company.

so if it just attacks/scans you can notify the IP's abuse address with the logs and they will generally disconnect the user.

if they have hacked you, unfortunately you will need to go through a legal chance to subpoena the details.

Emts your pretty much on the ball..I'll give some brief detail.

I own a site and this person must know me in person. And is inpersonating me and writing abusive things and posting my mobile etc.his used the same I.p twice out of the 4 times posting

  • 4 weeks later...

It's against the privacy act for an ISP employee to provide that information so either way you won't get far without formal legal action. If it's a serious incident then proceed, if it's just a punk impersonating you but not actually hacking in to your personal accounts or systems, then just laugh it off and move on. If the person is smart they wouldn't do anything that would get them in trouble from their own computer/network.... If all you have is an IP address - big deal. That doesn't equal the person you're looking for. I deal with attacks that come from random IP addresses and ASN's around the world and it's just not that simple to trace an IP address to an actual person. Whoever it is could be using someone elses network or computer and you wouldn't know. They could be using free wifi hotspots in the CBD. Good luck with that. But you might get lucky, some people aren't that smart.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...