Jump to content
SAU Community

Recommended Posts

Depends on vehicle height. I wouldn't say that 8" +32 or 8.5" +32 flush on the front of a R34 GTT is flush, not even close. It's not horrid, but it's not flush.

18 x 9" +30 is good but even that is not flush. 18 x 9" +30 front (235/40) and 18 x 10" +38 (265/35) rear is nice but still not hella flush.

If it's pretty low then 18 x 9.5" +22 would be stance, with 235/40 or 225/40 to tuck them under. AFAIK the R34 has a few mm more guard space than R33. I have R33 and 18 x 9" +25 would fit easy front and rear.

Link to comment
https://www.sau.com.au/forums/topic/442850-r34-gt-offset/#findComment-7280118
Share on other sites

Depends on vehicle height. I wouldn't say that 8" +32 or 8.5" +32 flush on the front of a R34 GTT is flush, not even close. It's not horrid, but it's not flush.

18 x 9" +30 is good but even that is not flush. 18 x 9" +30 front (235/40) and 18 x 10" +38 (265/35) rear is nice but still not hella flush.

If it's pretty low then 18 x 9.5" +22 would be stance, with 235/40 or 225/40 to tuck them under. AFAIK the R34 has a few mm more guard space than R33. I have R33 and 18 x 9" +25 would fit easy front and rear.

my bad, bad choice of words use. It is slightly inside the guard but close to parallel with the guard. My rims are work CR and running coilover with it's original height.

Link to comment
https://www.sau.com.au/forums/topic/442850-r34-gt-offset/#findComment-7280236
Share on other sites

Thanks for all the help guys, I went in and ordered a set of hyper black rota grid R's fronts are 18 by 8.5 and the offset is +35, rears are 18 by 9.5 +35 I also ordered some coilovers to get the rear a little bit lower. It should all be in stock by next week the guys said

Link to comment
https://www.sau.com.au/forums/topic/442850-r34-gt-offset/#findComment-7280681
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Bit of a pity we don't have good images of the back/front of the PCB ~ that said, I found a YT vid of a teardown to replace dicky clock switches, and got enough of a glimpse to realize this PCB is the front-end to a connected to what I'll call PCBA, and as such this is all digital on this PCB..ergo, battery voltage probably doesn't make an appearance here ; that is, I'd expect them to do something on PCBA wrt power conditioning for the adjustment/display/switch PCB.... ....given what's transpired..ie; some permutation of 12vdc on a 5vdc with or without correct polarity...would explain why the zener said "no" and exploded. The transistor Q5 (M33) is likely to be a digital switching transistor...that is, package has builtin bias resistors to ensure it saturates as soon as base threshold voltage is reached (minimal rise/fall time)....and wrt the question 'what else could've fried?' ....well, I know there's an MCU on this board (display, I/O at a guess), and you hope they isolated it from this scenario...I got my crayons out, it looks a bit like this...   ...not a lot to see, or rather, everything you'd like to see disappears down a via to the other side...base drive for the transistor comes from somewhere else, what this transistor is switching is somewhere else...but the zener circuit is exclusive to all this ~ it's providing a set voltage (current limited by the 1K3 resistor R19)...and disappears somewhere else down the via I marked V out ; if the errant voltage 'jumped' the diode in the millisecond before it exploded, whatever that V out via feeds may have seen a spike... ....I'll just imagine that Q5 was switched off at the time, thus no damage should've been done....but whatever that zener feeds has to be checked... HTH
    • I think Fitmit had some, have a look on there (theyre Australian as well)
    • Hah, fair enough! But if you learn with this one you can drive any other OEM manual. No modern luxury features like auto rev-matching or hillstart assist to give you a false sense of confidence. And a heavy car with not that much torque so it stalls easily. 
    • Actually, I'd say all three are the automatic option. Just the different trim levels. The manual would be RSFS, no? 
×
×
  • Create New...