Jump to content
SAU Community

New Plugs And Coils Car Not Running Right

polzin

By polzin,
in Engines & Forced Induction

 Share

Recommended Posts

polzin Enthusiast

polzin

Posted
Posted

ok so i put new coils on last week and worked awesome still had some spark breaking down issues but not as bad today i put in new plugs BPR5ES gap down to 0.7 now i put it all back together and fire it up it seems to be not firing on 3cyl or 6cyl i double check loose connections now i am lost :/

Ben C34 Grand Master

Ben C34

Posted
Posted

And after rereading your post, you disturbed the loom and it got worse, so that seems to point to the loom.

Is 5 heat range stock? That's a pretty hot plug. I use 7 heat range, most guys say go with 6 or 7. Not 5.

Ben C34 Grand Master

Ben C34

Posted
Posted

how i check them was pull each connetor of one at time to here to miss

That's the smart way to do it.

You can then swap coils and see if the miss moves, letting you pinpoint coil or loom.

polzin Enthusiast

polzin

Posted
  • Author
Posted

i got them off a member off here there is spark in cyl 3 going to test cyl6 after work i got a feeling it may be a boost leak but i think maybe the coil loom is on its way out so ill just pull it all apart again tomoz and see how i go with it all just a sill question say if i a plug the loom wrong like had one swapped around will this cause a miss?

MJTru Mentor

MJTru

Posted
Posted

What you might want to do is a compression test on all cylinder. After that's Ok. Take out all the coil packs and unplug them along with the injector harness. Then remove the CAS sensor and test by plugging in one coil at a time from any cylinder. Let's say number one. Turn the CAS sensor clockwise with the ignition key on holding the coil with spark plug in it . You will see the spark plug fire. That ecu channel would be good and coil and plug would be good as well if spark is present. Repeat this on all coil and ecu channels. You can use this method for injectors, but a noid light would be safer and easier. I have had this happen to me and it was the plug on the ecu.

Hope it helps mate.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • joshuaho96
      Cas issue

      By joshuaho96 · Posted

      Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • joshuaho96
      Jacks that fit under GTR lips that can reach the subframe?

      By joshuaho96 · Posted

      On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      Nice....looking forward to that update
×
×
  • Create New...