Jump to content
SAU Community

Gtm Twin Turbo Kit

V(35)Powarh!
 Share

Recommended Posts

scotty nm35 Grand Master

scotty nm35

Posted
Posted

I have seen plenty of e85 Walbro 460 results, and fitted over 10 myself. They are good for 400+wk easily, most of my results have been 430-450kw before running out of fuel.

They draw 20 amps on full load, I really hope you have run decent cable to it, through a fuse and relay...

R6n350GT Experienced

R6n350GT

Posted
Posted (edited)

stock wiring :/

i asked the tuner to check it was getting correct voltage and he reckoned it was..

DW Bosch IV14 1000cc

I have ordered the CJM twin fuel pump housing with one 485 and one 255.

Guess my 485 with -6AN return and -8AN supply fuel pump basket will be for sale soon!

I also have a DW300 fuel pump for sale too...

Edited by R6n350GT
scotty nm35 Grand Master

scotty nm35

Posted
Posted

Fark man, that's impressive. Get some decent wires to the pump quick smart. 30 amp fuse and a decent relay to suit. Use the old pump power wires to energise the relay.

I would say it's the injectors more than the pump, the 1000's maxed out at 330kw on my last customers car, (auto 34 skyline.) They don't seem to like high pressure either, I would try dropping your base fuel pressure if you have an adjustable reg, and perhaps get some Xspurt 1400cc ethanol injectors. You can sell the 1000's easily.

R6n350GT Experienced

R6n350GT

Posted
Posted

Fark man, that's impressive. Get some decent wires to the pump quick smart. 30 amp fuse and a decent relay to suit. Use the old pump power wires to energise the relay.

I would say it's the injectors more than the pump, the 1000's maxed out at 330kw on my last customers car, (auto 34 skyline.) They don't seem to like high pressure either, I would try dropping your base fuel pressure if you have an adjustable reg, and perhaps get some Xspurt 1400cc ethanol injectors. You can sell the 1000's easily.

Yeah i should have run a dedicated wire in the first place..

He said the 1000 were not the issue but fuel supply, maybe it was the lack of power..

Well if i still have issues with this new pump ill have too look into them. i hope not as im sick of buying new parts when the new part i just brought is not doing its job !

What is the price for a set of 6 with connectors?

scotty nm35 Grand Master

scotty nm35

Posted
Posted

The 1400's are $120 each.

If you had asked before buying the 1000's I would have told you, but the tuner should have been more forthcoming with previous results, surely he would know you are pushing it for the 1000's. (Unless he wanted to sell you larger injectors later?)

Seems a lot of these performance mechanics have no real clue when it comes to e85, 5 years behind the 8 ball for some reason.

R6n350GT Experienced

R6n350GT

Posted
Posted

Yeah who knows

i will be happy once i have a stable 500RWHP !

ill let u know how it goes

The 1400's are $120 each.

If you had asked before buying the 1000's I would have told you, but the tuner should have been more forthcoming with previous results, surely he would know you are pushing it for the 1000's. (Unless he wanted to sell you larger injectors later?)

Seems a lot of these performance mechanics have no real clue when it comes to e85, 5 years behind the 8 ball for some reason.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • joshuaho96
      Cas issue

      By joshuaho96 · Posted

      Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • joshuaho96
      Jacks that fit under GTR lips that can reach the subframe?

      By joshuaho96 · Posted

      On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      Nice....looking forward to that update
×
×
  • Create New...