Jump to content
SAU Community

Recommended Posts

Hey

I've done searches in regards to this, but there are differing opinions and not many proper answers...

I've dumped oil plenty of times. This time though, after letting the oil drain for about an hour, I went ahead and put in fresh oil. But I've accidently overfilled...

It's 4L engine + .4L oil filter on a RB20DET. Engine has done 150k.

I put about 4L in, let it sit, had a look at the dipstick and it showed above H. Went for a small drive, let it sit again, but still sitting about 4mm too high. The dipstick shows the oil level about 4mm above max. and it just touches the letter H.

Should I drain some out?

Cheers

Link to comment
https://www.sau.com.au/forums/topic/443919-rb20det-oil-overfill/
Share on other sites

Nah no dents, sump is all good. A fair bit of oil must have remained even after draining...

I think the best thing to do is simply get it at the correct level.

I'll see if I can drain some without undoing the plug completely, otherwise I'll dump the lot and then put it back in at the appropriate level.

Nah no dents, sump is all good. A fair bit of oil must have remained even after draining...

I think the best thing to do is simply get it at the correct level.

I'll see if I can drain some without undoing the plug completely, otherwise I'll dump the lot and then put it back in at the appropriate level.

Just to recap.

You come on here asking if the oil overfill is ok.

2 people say it is ok.

You somehow decide you should drain it.

Seems odd.

  • Like 1

Just to recap.

You come on here asking if the oil overfill is ok.

2 people say it is ok.

You somehow decide you should drain it.

Seems odd.

I don't know why you'd say that, I get asked for help all the time and it goes roughly like this:

*phone rings*

Me: "Hello"?

Caller: "Hi I need your help with X, it's doing Y"

Me: "I know what the problem is, you need to do Z"

Caller: "I don't think so, I reckon it's.............."

every. single. time.

I think people are just f*cking useless at asking for help.

To weigh in on the original conversation I fill between the H and the hump on an oil change (in an RB25 you can just dump 5L in if you have drained it on a level surface). I assume the hump is the danger zone much like there's a hump on the low side as well.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
    • EMU Classic. For what I need it to do I see no reason to upgrade. Link and Haltech would both cost an extra chunk of money for a lot of unutilized features
×
×
  • Create New...