Jump to content
SAU Community

Recommended Posts

Hey guys,

Just hoping everyone can keep an eye out for my 1999 s2 stagea (number plate: YRX 436) that was stolen tonight (08/07/2014 between 8:30pm and 10pm) outside a mate's place a Glen Iris, Victoria.

It's pearl white with black r33 wheels.

If you see it, please contact the police or me on 0422 897 384.

Thanks.

Link to comment
https://www.sau.com.au/forums/topic/444179-stolen-stagea/
Share on other sites

Hey guys,

I recently bought the car from a guy on this forum back in April.

Link of the ad:

http://www.skylinesaustralia.com/forums/topic/439137-fsft-1999-x-four-stagea-9000-ono/

However, since owning the car, i have added a tow bar, removing the stickers on the boot lid glass and swapping the rims to stock r33 rims that were spray painted black.

Cheers

Link to comment
https://www.sau.com.au/forums/topic/444179-stolen-stagea/#findComment-7308996
Share on other sites

There are a few gutter rashes on the rims, heaps of scratches on the front bumper and rips in the roof lining.

Will also need the ignition and door locks replaced.

Car smells like alcohol and smokes too.

Like I said, grateful for it to be back home.

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/444179-stolen-stagea/#findComment-7309901
Share on other sites

There are a few gutter rashes on the rims, heaps of scratches on the front bumper and rips in the roof lining.

Will also need the ignition and door locks replaced.

Car smells like alcohol and smokes too.

Like I said, grateful for it to be back home.

Glad to see you have it back!

Link to comment
https://www.sau.com.au/forums/topic/444179-stolen-stagea/#findComment-7309922
Share on other sites

No doubt they flogged the guts out of it.

Oil change, filter, brake pads, gear oil etc etc.

What a pain, and ill bet it never feels the same again.

I know my old 32 was stolen at some point in its life, The ignition barrel was stuffed.

3 years of fking around with new bushes, bearings, this and that. Its getting better now.

:/ Hope yours gets better soon.

Oh... and underneath, mine is hammered, so much the chassis is a bit off.

Edited by D.I.Y. Mik
Link to comment
https://www.sau.com.au/forums/topic/444179-stolen-stagea/#findComment-7309928
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...