Jump to content
SAU Community

Re-Building A Front Lip

nicr4wks

By nicr4wks,
in Exterior & Interior Styling

 Share

Recommended Posts

nicr4wks Experienced

nicr4wks

Posted
Posted

Hey Guys,

For the last 2 years I've been looking around for an R33 s2 mspec front lip, about a year a go I bought a front bar that had been in an accident with ~60% of the lip intact, it's missing a section that wraps around the passenger side. I'd like to have a crack at repairing the current lip or replicating a whole new one, where should I start? I've never done fiberglassing or molding.

I assume taking a mold of the drivers side would be required, then somehow 'flip' it so it's a mirror image for the passenger side? I'm not sure how I would go about that.

post-63773-0-56476700-1403136152_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/444625-re-building-a-front-lip/
Share on other sites
Hanaldo Grand Master

Hanaldo

Posted
Posted

You can actually ^ Not to make a mould, but given that piece of the lip is symmetrical, one can take a skin of the one side and flip it around to fit the other side. Works for things that are symmetrical and don't taper in a certain direction.

If you haven't done fibreglassing before then I'd advise playing around with it before attempting to fix your bumper. You might be better off trying to find another one, but have a play with some fibreglass and resin and see how you go. That said, this isn't the hardest of repairs. Nor is it easy to explain. One way to do it would be to cover the drivers side of the lip with clear packing tape (make sure it's the polythylene stuff), then use EPOXY (polyester shrinks and the styrene will attack your paint if it is exposed, nasty stuff) and woven fibreglass cloth to make a skin of each individual bit. Break it down into the bits that you can flip and fit into place on the passenger side. I'd estimate it is likely to be 3 pieces, the inner piece on the left that is partially cracked, the piece that runs along the bottom edge of the bumper, and the piece the sits on the side of the bumper. Get me? Then you can cut the lip off where it is cracked so it is square, and bond on your new pieces. Then feather them in using body filler, before spraying high build primer to fill the final low spots. Easy right?

75coupe Grand Master

75coupe

Posted
Posted

There are quite alot of complex shapes there to flip im not sure it would be of benefit using a flip method...

Id say just get a better one, there is a heap there to recreate especially if you havnt done it before

Hanaldo Grand Master

Hanaldo

Posted
Posted

Yes but you don't have to copy all of them. Just the ones that work, to give you a profile. Then you can fill the rest.

It's not the easiest job, but it's not super hard either. For a production item like this it's always going to be better to find another one though, unless you want to make it in carbon fibre ;)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • funkymonkey
      Jacks that fit under GTR lips that can reach the subframe?

      By funkymonkey · Posted

      I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      ..this is the current state of that port. I appreciate the info help (and the link to the Earls thing @Duncan). Though going by that it seems like 1/4 then BSP'ing it and using a bush may work. I don't know where I'd be remote mounting the pressure sender... to... exactly. I assume the idea here is that any vibration is taken up by the semiflexible/flexible hose itself instead of it leveraging against the block directly. I want to believe a stronger, steel bush/adapter would work, but I don't know if that is engineeringly sound or just wishful thinking given the stupendous implications of a leak/failure in this spot. What are the real world risks of dissimilar metals here? It's a 6061 Aluminum block, and I'm talking brass or steel or SS adapters/things.
×
×
  • Create New...