Jump to content
SAU Community

Recommended Posts

I'm hoping to come along in my Evo 6, came and watched the last one at lakeside and it looked like heaps of fun...

Problem is my Evo is in pieces and I won't get to work on it until Saturday.. hopefully I can make it

I'm hoping to come along in my Evo 6, came and watched the last one at lakeside and it looked like heaps of fun...

Problem is my Evo is in pieces and I won't get to work on it until Saturday.. hopefully I can make it

well you are going to be busy then,i did some weight saving and removed my ac unit and pump last week,luckily i did cause i found that i had split hoses on my actuator and the bov.seems to be pulling a lot harder now,must of been causing false readings as now my boost is 2 pounds lower but goes better,got me stuffed,anyway good luck and hope to see you there,always enjoy running with you evo boys and girls.

  • Like 1

well the evo is back together and holding boost as well as it was before (i.e. not very well at all), but it's good enough to drive and hopefully I'll be able to keep up with any NA cars :rolleyes:

well the evo is back together and holding boost as well as it was before (i.e. not very well at all), but it's good enough to drive and hopefully I'll be able to keep up with any NA cars :rolleyes:

thats the spirit,see you there.

Is this still on?
Tried to get out to fricking Willowbank tonight for test and tune, Cunningham Hwy was completely closed either side of champions way, with a sign detouring people right around, but no fricking sign telling people that test and tune had been cancelled.

http://highload.131940.qld.gov.au/

Cunningham Highway, Willowbank
Crash Multi-vehicle Highway closed both directions at Champions Way. Heavy vehicles please seek alternative route Both Directions
Medium delays expected
Diversions are in place

It should be cleared by the morning, hope no one was hurt.

awesome happy laps,got to run longer than normal cause nothing on after us,had a blast and would like to thank mike again for organising another successful happy laps and all the evo boys for coming along,had about 40 odd cars and everyone was well behaved,poor old legnum blow a coolant hose behind me on the second to last lap and i had an eventful slide the lap after on all his collant,and some oil as well i think cause i was sideways trying to get around the last corner before front straight.Didnt go off and i have to admit it was rather fun,and scary all at the same time.Now just got to fix my ps leak,and start saving up for some goodies,will be a work in progress but will slowly get the old girl to where i want.Will post some pictures later once i down load them.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...