Jump to content
SAU Community

Recommended Posts

Thanks for the responses. We'll the hta on twinscroll would be an even better combo would it not?

34geeteetee did you go from garrett gt3076r to hta 3076? And still happy with the results?

Are you running a single scroll 6boost low mount?

Edited by BlackBox

Thanks for the responses. We'll the hta on twinscroll would be an even better combo would it not?

34geeteetee did you go from garrett gt3076r to hta 3076? And still happy with the results?

Are you running a single scroll 6boost low mount?

Yes it was a back to back swap with awesome results!

No mine is high mount.

Any particular reason you went high mount? What size compressor and turbine housing did you get?

Not really, i likes the way it looked in engine bays and figured it would be easier to work on... If i was to do it again i would have the turbo sitting further forward to make it easier to work on!

The housing is still a 4 bolt 0.82.

You'd probably get lower underbonnet temps and the dump etc is shorter and less obvious looking, but its a pain to fit ,

post-70965-0-67475700-1404985532_thumb.jpg

post-70965-0-62393100-1404985560_thumb.jpg

I was bit disappointed with the twin scroll, quite laggy in my case, maybe the use of twin gates would of made it more responsive im not sure but gave up on it.

Edited by AngryRB

Larger than gt3076? Did not realise this, hopefully will be all good :/

Yes, same size cover as the GT35... I thought i mentioned it but might not have :/

Are you on a stock manifold or aftermarket? (Sorry couldn't be bothered going back a few pages lol)

Low mount with a GT35 compressor cover? Good luck getting that to fit, 6Boost manifolds don't allow many turbo's even top mounted.

The twin gate setups are very tight... I would externally gate the turbine housing on the stock manifold if you are heading down the low mount route.

If your going to go a HTA 3076 twin scroll and wan't 330rwkw on pump fuel then I would suggest a T3 1.01 or T4 1.06 twin scroll ex hsg. I would also suggest a twin gate twin scroll manifold over a single ...so then the costs start adding up once the associated plumbing is also factored in.

Running a HTA3076 or even a GTX3076 on a .78 twin scroll hsg will just limit the top end potential of these turbos with potentially additional lag over the Garrett GT counterparts. The biggest GT30 turbo I would run with the .78 hsg on pump fuel would be a T56 GT3076 and event then I'd say it could limit the top end potential of that turbo. I'm not even sure I would run a GT30 size .78 twin scroll hsg on a RB 25 period given your hp goals on pump fuel.

Low mount with a GT35 compressor cover? Good luck getting that to fit, 6Boost manifolds don't allow many turbo's even top mounted.

The twin gate setups are very tight... I would externally gate the turbine housing on the stock manifold if you are heading down the low mount route.

I tried to find pics of the 6boost low mount design and i remember it had to have a bit of the engine mount shaved to fit the comp housing even on the GT3076...

I was going to still run one gate with the twin scroll,.. Would retaining the standard low mount leave more room than the 6 boost low mount? Had anybody heard of hta3076 on standard exhaust manifold?

Geeteetee did you have your 6 boost manifold before upgrading to your hta?

Are you saying the t3 1.01 twin? Or only t4 twin scroll beside t3 twin would be a restriction ?

I was going to still run one gate with the twin scroll,.. Would retaining the standard low mount leave more room than the 6 boost low mount? Had anybody heard of hta3076 on standard exhaust manifold?

Geeteetee did you have your 6 boost manifold before upgrading to your hta?

Are you saying the t3 1.01 twin? Or only t4 twin scroll beside t3 twin would be a restriction ?

I was going to still run one gate with the twin scroll,.. Would retaining the standard low mount leave more room than the 6 boost low mount? Had anybody heard of hta3076 on standard exhaust manifold?

Geeteetee did you have your 6 boost manifold before upgrading to your hta?

Are you saying the t3 1.01 twin? Or only t4 twin scroll beside t3 twin would be a restriction ?

yes mine was always high mount!

Twin scroll options aren't really available for them either...

Maybe a TS GTX3071 will be a better option for more response and fitting low etc?

Your call with running one gate on a twin scroll setup.

I'm saying either a T3 1.01 or T4 1.06 but you would need to buy the hsg separately such as from GCG or the like.

Personally, if it were my car and I was budget conscious I'd stick with a single scroll setup with the HTA 3076 and run a 3.5 inch dump back to the cat to get the turbo on boost as soon as possible.

I run a twin scroll twin gate setup on my SR20 and love it.....but money was of no concern to me.

Edited by juggernaut1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Stock ECU (or more accurately stock tune) absolutely refuses to go over 10psi and behaves like you have seen. The Nistune is the same if it is the stock tune. If the Nistune chip has been tuned, the resulting tune could be literally anything for any combination of parts. The Nistune just makes the stock ECU Tunable.
    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
×
×
  • Create New...