Jump to content
SAU Community

Recommended Posts

Thanks for the responses. We'll the hta on twinscroll would be an even better combo would it not?

34geeteetee did you go from garrett gt3076r to hta 3076? And still happy with the results?

Are you running a single scroll 6boost low mount?

Edited by BlackBox

Thanks for the responses. We'll the hta on twinscroll would be an even better combo would it not?

34geeteetee did you go from garrett gt3076r to hta 3076? And still happy with the results?

Are you running a single scroll 6boost low mount?

Yes it was a back to back swap with awesome results!

No mine is high mount.

Any particular reason you went high mount? What size compressor and turbine housing did you get?

Not really, i likes the way it looked in engine bays and figured it would be easier to work on... If i was to do it again i would have the turbo sitting further forward to make it easier to work on!

The housing is still a 4 bolt 0.82.

You'd probably get lower underbonnet temps and the dump etc is shorter and less obvious looking, but its a pain to fit ,

post-70965-0-67475700-1404985532_thumb.jpg

post-70965-0-62393100-1404985560_thumb.jpg

I was bit disappointed with the twin scroll, quite laggy in my case, maybe the use of twin gates would of made it more responsive im not sure but gave up on it.

Edited by AngryRB

Larger than gt3076? Did not realise this, hopefully will be all good :/

Yes, same size cover as the GT35... I thought i mentioned it but might not have :/

Are you on a stock manifold or aftermarket? (Sorry couldn't be bothered going back a few pages lol)

Low mount with a GT35 compressor cover? Good luck getting that to fit, 6Boost manifolds don't allow many turbo's even top mounted.

The twin gate setups are very tight... I would externally gate the turbine housing on the stock manifold if you are heading down the low mount route.

If your going to go a HTA 3076 twin scroll and wan't 330rwkw on pump fuel then I would suggest a T3 1.01 or T4 1.06 twin scroll ex hsg. I would also suggest a twin gate twin scroll manifold over a single ...so then the costs start adding up once the associated plumbing is also factored in.

Running a HTA3076 or even a GTX3076 on a .78 twin scroll hsg will just limit the top end potential of these turbos with potentially additional lag over the Garrett GT counterparts. The biggest GT30 turbo I would run with the .78 hsg on pump fuel would be a T56 GT3076 and event then I'd say it could limit the top end potential of that turbo. I'm not even sure I would run a GT30 size .78 twin scroll hsg on a RB 25 period given your hp goals on pump fuel.

Low mount with a GT35 compressor cover? Good luck getting that to fit, 6Boost manifolds don't allow many turbo's even top mounted.

The twin gate setups are very tight... I would externally gate the turbine housing on the stock manifold if you are heading down the low mount route.

I tried to find pics of the 6boost low mount design and i remember it had to have a bit of the engine mount shaved to fit the comp housing even on the GT3076...

I was going to still run one gate with the twin scroll,.. Would retaining the standard low mount leave more room than the 6 boost low mount? Had anybody heard of hta3076 on standard exhaust manifold?

Geeteetee did you have your 6 boost manifold before upgrading to your hta?

Are you saying the t3 1.01 twin? Or only t4 twin scroll beside t3 twin would be a restriction ?

I was going to still run one gate with the twin scroll,.. Would retaining the standard low mount leave more room than the 6 boost low mount? Had anybody heard of hta3076 on standard exhaust manifold?

Geeteetee did you have your 6 boost manifold before upgrading to your hta?

Are you saying the t3 1.01 twin? Or only t4 twin scroll beside t3 twin would be a restriction ?

I was going to still run one gate with the twin scroll,.. Would retaining the standard low mount leave more room than the 6 boost low mount? Had anybody heard of hta3076 on standard exhaust manifold?

Geeteetee did you have your 6 boost manifold before upgrading to your hta?

Are you saying the t3 1.01 twin? Or only t4 twin scroll beside t3 twin would be a restriction ?

yes mine was always high mount!

Twin scroll options aren't really available for them either...

Maybe a TS GTX3071 will be a better option for more response and fitting low etc?

Your call with running one gate on a twin scroll setup.

I'm saying either a T3 1.01 or T4 1.06 but you would need to buy the hsg separately such as from GCG or the like.

Personally, if it were my car and I was budget conscious I'd stick with a single scroll setup with the HTA 3076 and run a 3.5 inch dump back to the cat to get the turbo on boost as soon as possible.

I run a twin scroll twin gate setup on my SR20 and love it.....but money was of no concern to me.

Edited by juggernaut1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I thought I'd do a write up on an auto transmission fluid change for a the nissan 7 speed Automatic. At some stage the genius engineers decided that the fluid in the trans was "for the life of the transmission", (which seems kind of self supporting to me) and removed the dip stick and fill tube (funnily enough there is still a casting for it). Anyway, for this job you do need 2 specialist tools in addition to regular hand tools, jack and good chassis stands. You need a way to pump fluid up to the transmission; I got one of these but there are plenty of other options: https://www.ebay.com.au/itm/364584087070 Don't trust the generic listing though, it does not come with the required adapter for the Nissan 7 Speed. You need one of these, can't do the job without it: https://navarapart.com.au/product/genuine-nissan-patrol-y62-d23-np300-navara-re7-dipstick-fill-connector1 You need a heap of compatible transmission oil. Could be Nissan, could be anything else rated for Nissan Matic S. You need at least 10 litres, I had 15 to give it a better flush... Also, you need some biiig oil catch trays, at least one of these, or bigger if possible (volume was fine, size was very marginal): https://autobarn.com.au/ab/Autobarn-Category/Tools-%26-Garage/Specialty-Tools/Oil-Service/Garage-Tough-Oil-Drain-Pan-Black-16L---GT1068/p/TO03191 Finally, a measuring jug is very useful if your pump does not have volumes marked on it, I got a 6l one: https://www.repco.com.au/oils-fluids/fluid-accessories/measuring-jugs/penrite-measuring-jug-6l-pmj006/p/A5322648 Oh, and gloves.....this stuff is horrible (not as bad as diff oil, but getting there) ....First, jack up your car.....
    • So I mentioned the apprentice, @LachyK helped take the bonnet off. We just undid the nuts on the hinges and unclipped the gas struts, then pulled the bonnet back a little as the front was catching on the front bar.  I had a good look at everything today and have removed the rams, repaired/reset the hinges and bolted it back together like it never happened. I'll do a separate write up on the repair, and I also removed the poppers from the Fuga today too to save grief down the road.....as said above it is at least $5k to repair retail. I'm also happier about my ability to prepare a race car, and less happy about Nis-nault's engineering (I can hear @GTSBoy sAfrican Americaning) because the top hose of the radiator didn't slip off.......it snapped clean off. By practice I put the hose clamp hard up against the flare on a neck to make it least likely to ever move (thanks @Neil!). I guess that puts a little more pressure on the end of the pipe as it is further away from the rad, but still, that is pretty shit. I've put it back on for now as there was a fair bit of neck still there, but obviously there is no lip on the neck any more so I don't think I'll track it again until I have a new rad. Speaking of which....more research required. It looks like Koyo makes a standard size radiator in ally which I'll grab in the meantime, but I really want something thicker so might have to go custom in the medium term (ouch) Coolant still needs a refill and I have the pressure tester on it over night, but other than a wash down of the engine bay it seems alright. And @MBS206 noted something noisy on the front of the engine and I think I agree....time for a new accessory belt and tensioners I think.
    • our good friends at nismo make a diff for it, I have one (and a spare housing to put the centre in) on the way. https://www.nismo.co.jp/products/web_catalogue/lsd/mechanical_lsd_v37.html AMS also make a helical one, but I prefer mechanical for track use in 2wd (I do run a quaife in the front, but not rear of the R32)
    • What are we supposed to be seeing in the photo of the steering angle sensor? The outer housing doesn't turn, right? All the action is on the inside. The real test here is whether or not your car has had the steering put back together by a butcher. When the steering is centred (and we're not caring about the wheel too much here, we're talking about the front wheels, parallel, facing front) then you should have an absolutely even number of turns from centre to left lock and centre to right lock. If there is any difference at all then perhaps the thing has been put back together wrongly, either the steering wheel put on one spline (or more!) off, and the alignment bodged to straighteb the wheel, or the opposite where something silly was done underneath and the wheel put back on crooked to compensate. Nut there isn't actually much evidence that you have such a problem anyway. It is something you can easily measure and test for to find out though. My money is still on the HICAS CU not driving the PS solenoid with the proper PWM signal required to lighten the load at lower speed. If it were me, I would be putting either a multimeter or oscilloscope onto the solenoid terminals and taking it for a drive, looking for the voltage to change. The PWM signal is 0v, 12V, 0V, 12v with ...obviously...modulated pulse width. You should see that as an average voltage somewhere between 0V and 12V, and it should vary with speed. An handheld oscilloscope would be the better tool for this, because they are definitely good enough but there's no telling if any cheap shit multimeter that people have lying around are good enough. You can also directly interfere with the solenoid. If you wire up a little voltage divider with variable resistor on it, and hook the PS solenoid direct to 12V through that, you can manually adjust the voltage to the solenoid and you should be able to make it go ligheter and heavier. If you cannot, then the problem is either the solenoid itself dead, or your description of the steering being "tight" (which I have just been assuming you mean "heavy") could be that you have a mechanical problem in the steering and there is heaps of resistance to movement.
    • Little update  I have shimmed the solenoid on the rack today following Keep it Reets video on YouTube. However my steering is still tight. I have this showing on Nisscan, my steering angle sensor was the closest to 0 degrees (I could get it to 0 degrees by small little tweaks, but the angle was way off centre? I can't figure this out for the life of me. I get no faults through Nisscan. 
×
×
  • Create New...