Jump to content
SAU Community

Recommended Posts

ok this is a different question to Waz's...

I got a 3" cat back installed on Friday (hi-flow cat, 3" piping w/ 4.5" cannon) it's damn loud...as in I don't think I'll pass the EPA dB test.

Question is, how do I make it quieter? Or should I change back to 2.5"?

The other thing is when it's idling it sounds a little lumpy. Now the car's fairly stock. The only mods I'm aware of are the ones I've done (front mount, pod). There is also a Blitz BOV. Just wondering if this lumpy sounding idle is normal or does it sound like my car had some previous work done that I'm unaware of.

Link to comment
https://www.sau.com.au/forums/topic/44560-3-exhaust-on-r32-gts-t/
Share on other sites

nah cereal your car just has that crazy note from the exhaust.

its probably not that bad but you are soft :rofl:

get an exhaust shop to fit a resonator should quiten it down a bit.

but you will loose power.

so dont come back grumbling I want more power :rofl:

any way have a listen to my car that has a similar exhaust but on an sr I have no hassels with it but I dont fang it through shopping centers etc.

teh efficence of turbo all come back to how quickly you can get the exhaust out with out restriction.

vid is here http://www.meggala.com/ceffyshort.MPG

cheers

meggala

this is why i was thinking of just going to a 2.5" cat-back...

how does a resonator work? is it straight-through in design like a muffler and how does it rob power?

you could just run 2 resonators if it will only lose you 5kW overall (a fair sacrifice in my opinion for ride comfort.

Mine is pretty quiet but i am running a 3" cat, centre and rear mufflers.

I would think that throwing a centre muffler / resonator could be the answer.... my old R31 has a custom 3" exhaust with only a rear muffler and a high flow cat, and it sounded absolutley wicked, loud sure but so much better then my R32, mind you it did have a pretty on/off T3/4 as well.

Me thinks cat and two mufflers is the way to go, just make sure they are good quality straight thru mufflers and they shouldnt knock the power around too much on a car with std turbo, or slightly biiger aftermarket jobbie.

Yer mines not loud at all.

With my other half driving my car normally and myself in a dunga door VN with the windows up I can't even hear my 32.

When she gives it stick I can hear it a little, when I put the windows down it is loudish but not a crude loud that is over the top. It is definately louder than some of the jap exhausts I've heard though.

I mentioned before I've got a turbo back 3", 3" cat, large center resonator and a large rear muffler.

Here's a pic of the rear muffler I am using.

muffler.gif

And another before the pipes are welded on.

200rear.gif

The resonator.. (Pics from a R33 GTR they also done)

gtrmuffs.jpg

And the Cat.

cat.gif

ok this is a different question to Waz's...

I got a 3" cat back installed on Friday (hi-flow cat, 3" piping w/ 4.5" cannon) it's damn loud...as in I don't think I'll pass the EPA dB test.

Question is, how do I make it quieter? Or should I change back to 2.5"?

The other thing is when it's idling it sounds a little lumpy. Now the car's fairly stock. The only mods I'm aware of are the ones I've done (front mount, pod). There is also a Blitz BOV. Just wondering if this lumpy sounding idle is normal or does it sound like my car had some previous work done that I'm unaware of.

exhaust noise = power :)

mine is 3", race cat :) and only the rear N1 muffler, almost completley straight through - its reasonably loud, but I love the sound of it, especially under a bridge or through a tunnel. It had the centre muffler section, but this was removed due to clearence issues getting into my car park at work.

Clint32 replaced the centre muffler section with straight through 3" and tucked the exhuast closer to the chassis

Been through bretho's etc, and under idle its reasonably quiet, no cops have ever looked twice at it. I'd say it would be very close to, or over the legal limit. Sets car alarms off in car parks sometimes

I'd say if you can put up with it, stick with the 3", and maybe get a resonator put in near the diff/cradle, as that will knock a few Db from it

I am thinking of putting the centre muffler back in, on long drives it can get a bit loud, so might whack it back in.

Try a resonator, you might loose a few rwkw, but thats the trade off for a bit quieter exhaust

Chris

Hi cerealeater, we always fit 2 mufflers to road cars, one around the gearbox (called a resonator by some) and one at the rear. Whether it is a 2.5", 3", 3.5" or 4" system we specify 2 mufflers, this fixes the resonance the annoying at certain rpm's. The power loss (if the mufflers used are efficient) is neglible. It's no good having an extra 20 rwkw if you can't drive the car because of the exhaust noise.

Hope that helps

i think i might get mine done in 3" (already have 3" dump/front), going:

turbo-> 3"dump -> 3" front -------> 3"cat -> 3" muffler -> 3" resonator ------------------> 3" cannon muffler

all straight through in design and all the same diameter

fair trade off for the power me thinks :)

(those lines are suppost to represent the approximate distance of pipe beween each component)

i have a 3inch straight thru and had a 5 inch muffler and it was to loud so i went and spoke to a muffler shop and they showed me a few mufflers that they thought would do the trick so i picked one and it worked perfectly and didnt notice a drop in power, but dont ask me the brand cause i would not know.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I saw you mention this earlier and it raised a red flag, but I couldn't believe it was real. Yes, the vacuum signal should vary. It is the one and only load signal from the engine to the ECU, and it MUST vary. It is either not connected or is badly f**ked up in some way.
    • @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
×
×
  • Create New...