Jump to content
SAU Community

Recommended Posts

Hi people, this car is really starting to do my head in! Car has never thrown a cel or missed a beat. Here goes car has new hi flow turbo, new plugs, pressure tested intercooler set up new intercooler claps etc etc . new big trans cooler , full trans flush. Does not use oil. Big dump pipe, hiflow cat 100cel. Car use to pull like a train, but not any more its sad. All it does now is bellow grey black smoke and lucky to out run a hyundai xcel.. Im lost for ideas??

Link to comment
https://www.sau.com.au/forums/topic/446280-slow-and-smokey-nm35/
Share on other sites

Should'nt that throw a cel but? Plus it surges on and off on boost.. Like the gate on turbo opening and closing constantly even holding your foot on throttle at the same point. Should your waste gate actuator have a tension spring on it? Mine does:-/

Probably is the bov making noise, not the waste gate. Is it misfiring while it does this? If the entire intake from afm to engine holds 30psi then it is most likely afm or a misfire issue ie fouled plugs, coil packs, poor compression. Eg. Mine has had Intake leaks, fouled plugs and faulty coil packs and hasn't thrown a code. I believe others have had their afm die without throwing a code also.

  • Like 1

All sorted :-) Had turbosmart boost controler on pipe from intercooler pipe to tb, totally blocked so no pressure getting to wastegate. And hose from cam cover to turbo inlet cut off and pointing to the ground:-0 Im guessing till you get to pressure off vacuum car can suck un metered air until pcv shuts.. if im correct??

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Working through possible solutions of converting my mechanical speedo.    Anyone know what type of speedo sensor the factory r34 gtr getrag has ? what the output is ? I assume its not a VSS and more a voltage like earlier speedo sensors ? Can an ECU read it ?  
    • roof rail delete used to be a thing, they were made locally for a while too
    • I can get more photos of it here soon and I plan to make a thread detailing the process. I received the car this way and it sorely needs refinishing. That is probably the most appealing photo of it. Up close it is fading, cracked, and needs to be re-glued. Depending on their condition I'm on the fence between refinishing or making a new set.  Another angle hiding the pimples and razor pumps  
    • According to this thread the RS4V with build plate RC40 comes with the R200 diff @ 4.083 ratio as well (mine has said RC40 denotation). We may need to check if the axle stubs are the same pattern as well. The auto subframes have longer axles. However I think yours being a later Series 2 as well, we should have the same bolt pattern for the diff stubs. Unless your upgraded rear also has upgraded axles. Either way, I would not be opposed to pulling the covers to check so I can inspect that  fancy rear core  Also I don't have HICAS. I don't believe that should change things but I hope the people here with heaps more experience than me can correct me if I'm wrong   Let me know if you want to attempt to make this work and I can get some pictures of mine from under the car. 
    • It's not that straightforward. For example I have had this code because my ignitor/power transistor wires were unplugged. It knows something is wrong but has no idea what it means. If you want to actually diagnose this I recommend following the service manual flowchart for code 21. Ohm out the harness, coilpacks, inspect the ECU, etc. And again, it's entirely possible for there to be no problem at all but if you're running a different coilpack it'll trigger the code because it doesn't like what it sees.
×
×
  • Create New...