Jump to content
SAU Community

Recommended Posts

Hi guys,

I'm a newbie here, and I don't actually own a Skyline (yet). However, I've got a number of good questions for you, so thanks in advance!

I'm considering an R33 GTR, and want to get around 500hp (flywheel) out of it. I'm wondering which parts would be the best for this (with some room left for higher outputs for the future), and approximately how much they will cost in total, incl. labour and tuning time? I don't want to lose too much bottom end torque, in other words, it has to be very driveable, and will mostly be used as an "everyday" car, but I anticipate I'll start going to the drags, also do a bit of track work, etc. etc. :) Oh yeah, I want to be able to run the car on 98 octane fuel as well :D

I spotted this video of an R34 GTR by MINE: http://racingflix.com/getvideo.asp?v=293&p=6

According to someone at the forum, it has 600hp (not sure whether at the flywheel or wheels). Now *that's* what I'm after. Someone on there also mentioned that it uses two 2530's, which I've also seen a few people recommend in here. Although you never really see the car below 4000 rpm, the power band seems to be fairly linear, which is what I'm looking for.

Now this may seem like a stupid question, but as far as I can see, there's no other way of asking it: is the amount of power (and driveability) you get for your money directly proportional, or are there "points" along the way where you may as well spend a relatively small amount for a relatively big gain? I'm asking this because I figured you guys would be able to help me with my 500hp goal. Should I go for 600hp (what I'd really like, but beyond that is a long way off :) ), or is that a lot more money? In other words, is 500hp for a GTR a good "point" or is it better value (in terms of $/kw) to go for, say 550 or 600hp?

In case you're wondering about my budget, well I'm not exactly sure, as I don't have the car yet (figuring around $35K for one with :)

OK then, that's about all I can think of for now,

Ben

Link to comment
https://www.sau.com.au/forums/topic/44649-how-much-will-this-cost-me/
Share on other sites

Ben,

Depending on the condition of the motor you can run 500hp at the fly all day on stock internals with a good tune. Once you start heading towards 600hp it's rebuild time sooner rather than later which will add around 10k to your bill...

I'm running 2530's, bigger cooler, PFC, 700cc injectors, Z32afm's, twin plate clutch etc and have around 420hp at all 4 wheels on 1.3bar.. You do get used to the power but it is still a seriously fast street car at that level. The 2530's boost up pretty much the same speed as the stockies, but midrange and top end is WAYYYYYY better...

To answer your question regarding money spent v's gains, the first few thousand you spend will net you the biggest jump in power, Ie exhaust, boost, turbs etc.. After that you start spending more on reliability and safeguards (ie bigger injectors, fuel pump etc).. These will allow you to run more boost to get more power but the gains won't be as great as the first couple I mentioned.

If you intend to mod the gtr and run it on 98 octane then some sort of aftermarket management will be required... Lots of different choices, I'd go for one that a local tuner you trust has experience with..

In the end, 500hp is not hard to get out of a gtr with minimal bolt on mods and will be very lively to drive on the street and around a track.. You'd be looking at mid 11's on the strip with around that power too....

Cheers

Brett

OK thanks guys for all the info!

I just had another idea, which again seems pretty stupid, even to me :mad:

What about a triple-turbo GTR? I don't think I'd ever attempt it myself, but rather than buying two new turbos, how about simply adding on a 3rd stock turbo? Assuming you've started with a stock car, would the work required to get this idea working be more than simply buying two bigger turbos? But for the "wow" factor, I like the idea of a triple-turbo! :)

So mesh, how does your car drive? What about the clutch? Is it OK or a bit of a bitch? That's one other thing I forgot to mention - I'd like the clutch to be fairly smooth and progressive if possible, unlike some of these nasty ones I see floating around that are basically "on" or "off" ;) So, if I spend a bit more on tuning, I could possibly get a better bottom end response?

Now this is something totally unrelated: my dad reckons that one of his friend's sons has an older Supra with a hand-controller thing (don't know the name ;) ) which allows him to adjust the ECU, which he apparently picked up for around $80. This guy's a bit of an engineering/mechanic-type guy, and the thing allows you to put some presets in for how you want to drive. He has one for performance, fuel economy, etc. etc. Is this the same as what one of those aftermarket ECU's will do, except it's not pre-tuned? Is it possible to get one of these for the Skyline, and how hard is it to use one? What about getting one pre-tuned by an expert, then messing around with it yourself afterwards to try and improve on it? I know you obviously have to know what you're doing, except I wouldn't mind having a play around with one. My dad's OK with this sort of stuff, so if I ever got into any sort of trouble, I'm sure he'd be able to undo my work ;)

Ben

Edit: oh and BTW, it seems my guess of $10-15K for mods was about right, looking at the linked thread. I think I'd stretch to $16,730 for 320rwkw. BTW, what drivetrain loss is factored in for GTR's?

Nope, didn't think a triple turbo would be easy, as I've seen a triple turbo Supra and the amount of pipework on that was ridiculous. But still, someone's gotta attempt it! :)

Oh yeah, but with that Supra I think the guy still wanted the sequential setup, which would have added a lot of pipework. So with a straight triple-turbo setup, how hard could it be? :jk:

Ben,

Considering that 3 out of the first 4 responses you got were from guys with Midnight Purple R33 GTR's I think that says a lot about how rare the colour is.. There would be at least another 3 or 4 R33's that colour on the forums, and I would say over 50% of R33 GTR's I see in mags owned in aust. are midnight purple!!!!! ha ha ha

What i think is very important, and seems to take a bit of a back seat in the modification stakes, are things like suspension/tyres/light weight components/weight saving. If you're after better response and driveability, don't just focus on getting more horsies.

cheers

EVL, since I'm new to these forums, I don't know anyone here, so I didn't know what colour car they owned. Your avatar is sort of ghosted so I can't tell the colour properly, and I can't see any links to pics of your car.

What I meant about rare is that I don't ever recall seeing one on the road. I usually take note of the colour of Skylines as they drive past, and most seem to be silver, black, white or dark red. Oh yeah, blue as well :) Was Midnight Purple a colour specific to the R33 and/or GTR model?

SS8, thanks for the suggestion. I think people go for more horsepower because it looks more impressive on paper. Also, and I'm just guessing here, I would say that decreasing the weight of the car would cost more than increasing the power. I was also planning to do a good suspension/tyres job as well, but that would be on top of the engine mod costs. Trust me, I know the importance of these things, so they certainly weren't taking a back seat to engine mods. However, I do have a better idea of the cost of these, whereas there are so many damn options and combinations with the engine mods that I just wanted to know the most reliable and cheap way to get the power/driveability that I want.

Ben

Ben, I didn't mean anything nasty by the post, it was more a poke at how many midnight purple GTR's we have on the forums... For a supposedly 'rare' colour there are a lot of them around the place!!!! ha ha ha

It is a factory colour for R33 GTR's, though they did release an anniversary edition GTS25t in the same colour. And R34's have Midnight Purple II and III in their colour range.

Getting back to the point of your thread, I'd suggest going to a couple of SAU cruises and picking peoples brains about what mods worked the best etc. You might even score a ride or three in a couple of 500+hp GTR's to get an idea of just how much fun they are..

Cheers

Brett

What i think is very important, and seems to take a bit of a back seat in the modification stakes, are things like suspension/tyres/light weight components/weight saving. If you're after better response and driveability, don't just focus on getting more horsies.  

cheers

Very good point SS8_Gohan, "something I'd like to do on the next car". And as comparison, the cost to get 260-280kw at the wheels from a GTR is minimal, exhausts, computer and some boost. probaly $2500-3000.

The next stage, like what I have done will get you 310-340kw at the wheels and wil cost an extra $11-14,000K. Some might say why only an extra 40+KW? which doesn't really explain the power benefits, because the power gain is everywhere in RPM range and not just the top end.

In hindsight, you could save the $11-14,000K, and spend it on weight reduction/suspension. I think with that sort of money you should easily loose 200-300kg, by replacing stock panels with carbon fibre.

I spoke to someone who plans on doing a similar project with an R32 GTR, who got a quote from that carbon mob in sydney/or queensland "forget exactly" to replace the bonnet, front bumper, front guards, rear boot, and door with carbon fibre for around $7-8K. The beauty is you can paint them to look stock... just not sure about safety & ADR.

This thread has a lot of good information on the Mines Response R34 and the kind of mods that will make you car more responsive:

http://www.skylinesaustralia.com/forums/sh...ead.php?t=33247

You can find a complete rundown on the parts in the Mines car at their website although the sum of the parts does not equal a responsive car: so much of it has to do with the magic tuning :)

http://www.mines-wave.com/Demo-Car/R34gtr/index.html

meshmesh: that carbon mob was probably Custom Carbon -- http://www.customcarbon.com.au/default.html

I think you would have a heard time with the ADRs if you replaced the doors... What I want is a carbon fibre prop shaft.

Lucien.

thanks lucien,

I have a picture of the mines R34N1 where my wedding photo should be :) :).

We concluded a number of thing from those threads... It's unlikely MINES would fully disclose the actual parts/mods list. One thing where are led to believe is that the R34 uses R33 GTR Diffs for the lower gearing coupled to the 6speed box, which enhance's it's response. Only by watching the vid is it possible to explain how unbeliebably "FAAAST" the Mines car revs through the range.

Yep, there the guys... Custom Carbon -- http://www.customcarbon.com.au/default.html

Yeah, I am sure even if you copied exactly what is listed on the Mines website (or listed in the BMI video) it wouldn't be as responsive as their car, but that's no reason not to try because you would still end up with a damn responsive car IMHO.

LW.

Ben,

Considering that 3 out of the first 4 responses you got were from guys with Midnight Purple R33 GTR's I think that says a lot about how rare the colour is..   There would be at least another 3 or 4 R33's that colour on the forums,  and I would say over 50% of R33 GTR's I see in mags owned in aust. are midnight purple!!!!!  ha ha ha

I know of TWO Midnight Purple GTRs in NSW.

Just because they're like whores in Melbourne, doesn't mean that they're common in the big picture :) It's a fact that there were a LOT less Midnight Purple GTRs made than say Silver, White and Black ones.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
×
×
  • Create New...