Jump to content
SAU Community

Issue Switching Between E85 And 98

nj1

By nj1,
in Engines & Forced Induction

 Share

Recommended Posts

nj1 Enthusiast

nj1

Posted
Posted

Hi all,

My car normally runs united e85, but fuel was low in the car and I put in 98, but the car appears to misfire/cut at 5000rpm in second gear with medium throttle.

The car is R32 RB20det, has eflex sensor and it is tuned to run on both e85 & 98.

The car had not been driven for 3 weeks either.

Any ideas on what the issue could be?

Link to comment
https://www.sau.com.au/forums/topic/447920-issue-switching-between-e85-and-98/
Share on other sites
Ben C34 Grand Master

Ben C34

Posted
Posted

Well the tune is scaled non linearly between 98 and e85 timing wise. There's a chance that the tune is off in between, as you probably still have some ethanol in there now. I would imagine straight 98 would still be the same as it was before, they wouldn't have had to change it.

Piggaz Grand Master

Piggaz

Posted
Posted

Drain tank again and put more 98 in it. You'll be surprised at how much E85 is still floating around when you thought it was "close to empty". Better yet, take the return off the regulator and let some flush through the system.

nj1 Enthusiast

nj1

Posted
  • Author
Posted

Drain tank again and put more 98 in it. You'll be surprised at how much E85 is still floating around when you thought it was "close to empty". Better yet, take the return off the regulator and let some flush through the system.

I did the opposite and filled it right up with e85, 0.70 tank e85 & 0.3 tank 98, plugged the lappy into the ecu and got 54% ethanol. It has still has the miss, I guessing the 54% is too far away from the 85% it's been tuned to on ethanol and tune isn't adjusting correctly?

Ben C34 Grand Master

Ben C34

Posted
Posted

I did the opposite and filled it right up with e85, 0.70 tank e85 & 0.3 tank 98, plugged the lappy into the ecu and got 54% ethanol. It has still has the miss, I guessing the 54% is too far away from the 85% it's been tuned to on ethanol and tune isn't adjusting correctly?

If you paid for a flex fuel tune you haven't got one by the looks of things. Have a chat to your tuner.

Piggaz Grand Master

Piggaz

Posted
Posted

You're 31 % away. Lol

Do it again.

Depends what you have paid for

A "flex tune" or E85 and a 98 tune. Having the fuel willy nilly in the middle of no where, of course it's not going to run right.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      Nice....looking forward to that update
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      Neg, the top one is actually for the front. The sizes are 18x10.5 +18 and 18x11 +32.   I measured many times but I'm sure I'll have problems as this is the thread for problems.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      Just one thing; tapping tapered threads is tricky. Taps are always tapered and you would generally run it as far as you can, but with a tapered thread you have to stop much sooner otherwise the wide part of the taper will run in too far and you will have to thread the sensor in too far too as well (possible that it will never make a good seal) BTW nice wide wheels, I guess the top one is for the back!
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      Welp, good to know. Will have to wait awhile until steady hands with drills and taps are available. In other news, these just arrived! I will weigh them for posterity. Edit: 11kg each (or 10.9/11.1 depending on what my scale decides over multiple tests, the 18x11 don't seem to weigh noticeably any more than 10.5)  
×
×
  • Create New...