Jump to content
SAU Community

Recommended Posts

Hey guys,

I'm looking at getting a new bumper for my series 2 R34 GTT Skyline. I was just wondering if there's any difference between the Series 1 and Series 2 front REO?

The front bumper I'm interested in is this:

http://cgi.ebay.com.au/ws/eBayISAPI.dll?ViewItem&item=271544985516

I know I need to purchase new indicators for it, but do I also need to change the Series 2 REO to a Series 1?

Thanks!

Just incase someone finds this via google...or search..

All the headlight support parts (the black bits) are different on a S2 and S1 R34.

The "Reo Bar" is the same, though.

Here's my crap picture:

http://imgur.com/nGuVPJ5

RED = DIFFERENT BITS ON S2 AND S1 (there's another under-headlight bracket on the side that isn't viewable obviously)

GREEN = SAME PART ON S1 AND S2 R34. THIS IS THE BIT PEOPLE USUALLY CUT TO FIT FMICS.

Hence the "is the reo the same on s1 or s2?" depends on what people mean by "reo" as the entire thing (reo+headlight supports) is often referred to as "a reo bar"

  • 9 years later...
On 22/9/2014 at 10:41 AM, Kinkstaah said:

Just incase someone finds this via google...or search..

All the headlight support parts (the black bits) are different on a S2 and S1 R34.

The "Reo Bar" is the same, though.

Here's my crap picture:

http://imgur.com/nGuVPJ5

RED = DIFFERENT BITS ON S2 AND S1 (there's another under-headlight bracket on the side that isn't viewable obviously)

GREEN = SAME PART ON S1 AND S2 R34. THIS IS THE BIT PEOPLE USUALLY CUT TO FIT FMICS.

Hence the "is the reo the same on s1 or s2?" depends on what people mean by "reo" as the entire thing (reo+headlight supports) is often referred to as "a reo bar"

Thanks for this, exactly what i needed to know

 

- sent from the future

  • Like 1

I should also say that the while they are different the only parts that matter are the center headlight supports and center bar from S1 to S2. The center bar will work, but the S1 has holes that clips go through into the S1 bumper. So if you were super cheap you could simply drill the S2 bar. Same thing with the side/wings. They have slightly different 'clips' but can be made to work.

The center headlight brackets however, cannot.

This is also where the GTR differs, which has a different center bar, and different headlight supports (to either GTT system), it also has different 'wing' headlight supports which is what I am calling under the headlight. However those CAN be made to work with the GTT Reo for a GTR front bar by a small spacer and a drill/tapping a thread into the reo because the bolt positions are slightly different.

So people only really need the center brackets to go between GTT S1, GTT S2, and GTR if you are happy to do some tinkering.

24 minutes ago, Kinkstaah said:

I should also say that the while they are different the only parts that matter are the center headlight supports and center bar from S1 to S2. The center bar will work, but the S1 has holes that clips go through into the S1 bumper. So if you were super cheap you could simply drill the S2 bar. Same thing with the side/wings. They have slightly different 'clips' but can be made to work.

The center headlight brackets however, cannot.

This is also where the GTR differs, which has a different center bar, and different headlight supports (to either GTT system), it also has different 'wing' headlight supports which is what I am calling under the headlight. However those CAN be made to work with the GTT Reo for a GTR front bar by a small spacer and a drill/tapping a thread into the reo because the bolt positions are slightly different.

So people only really need the center brackets to go between GTT S1, GTT S2, and GTR if you are happy to do some tinkering.

Awesome to know. I have a Series 1, and When pulling my front bumper off for the first time i realised my reo/crash bar was a bit worse for wear, and was going to try pick up a better one soon just so i can replace it. Someone is selling a full series 2 front bar and brackets for a decent price, so was going to probably reuse my brackets and install the new second hand reo/crash bar. I also have a genuine Altia body kit to do up, spray and put on, and not sure if that will use the series 1 or series 2 brackets for the front bumper, so having both will be handy, and knowing i can drill holes out to make stuff fit between series is also handy to know!

Yeah truthfully it seems like the headlight supports for the ALTIA and S2 should be the same, but they aren't. I can only guess that the grill area of the Altia bar is different to the grill area of the S2 bar. Either that or it's due to the S1 bar having an angle up to the center bar that the Altia doesn't, or something.

That said, I recently bought an Altia bar myself, and I fit it over the S1 brackets and thought "Yes, this will all work fine" so even as I doubt my own words as I post, I also daresay you'll be okay.

2 minutes ago, Kinkstaah said:

Yeah truthfully it seems like the headlight supports for the ALTIA and S2 should be the same, but they aren't. I can only guess that the grill area of the Altia bar is different to the grill area of the S2 bar. Either that or it's due to the S1 bar having an angle up to the center bar that the Altia doesn't, or something.

That said, I recently bought an Altia bar myself, and I fit it over the S1 brackets and thought "Yes, this will all work fine" so even as I doubt my own words as I post, I also daresay you'll be okay.

Well as I will have both S1 and S2 front parts i will see what works best out of the two. Im not fussed if i need to drill extra holes, and im a big fan of Nutserts/rivet nuts and a nice painted dome head bolt as a way to hold stuff in place where plastic clips have broken and are hard to source new ones

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...