Jump to content
SAU Community

Rb26 One Piece Bucket? Shim And Lifer

DannyzGTR

By DannyzGTR,
in Engines & Forced Induction

 Share

Recommended Posts

doo doo Proficient

doo doo

Posted
Posted (edited)

I still don't understand why? Lol they are only +1mm, not like its 2 Or 3mm. When clearly the aftermarket cams are 30mm base standard is 32mm.

So you don't keep throwing shims running smaller base circle cams. With the tomei buckets you use standard size shims, do the math mentioned above.

Or you could look for a one piece bucket and shim which, if it exists, would be at least as much as tomei plus you'd almost be guaranteed to have to buy a few more when a couple of the clearances end up being a little out. Subaru do this with the later ej's- makes redoing seats/refacing valves much more expensive.

Edited by doo doo
iruvyouskyrine Grand Master

iruvyouskyrine

Posted
Posted

I believe there is a company in the US that make one pieces for Toyota UZ engines after not liking the standard shim over or shim under setup. Was ages ago I was reading it but may be worth investigating see if they made any for RB's.

r33_racer Grand Master

r33_racer

Posted
Posted

Shimless is obviously the best way to go if you can sort it out.

Anyone running that kind of setup, what is standard practice for a head rebuild if required? I assume you need to grind the tips of the valves or top of bucket in order to reset lash after a valve/valve seat regrind?

If it was possible, which I don't think it is with standard valve lengths is using lash caps instead of shims. Far harder to flick a lash cap then it is a shim. But I don't think there is enough valve tip protrusion above the retainer on a std setup in order to utilise a cap.

  • 5 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • 33GTRV
      Rb26 iron block limit

      By 33GTRV · Posted

      Here is a recipe. Sonic blocks till you get one that has a good enough bore. Get a torque plate and block brace, use your choice of fasteners (arp ect) bolt the thing together empty, half fill it and let it cure. Release it when it has, go to a REPUTABLE RB Builder and get the thing line bored/honed and cylinder honed to size, then wash. Once its all clean and dandy, wash and blow it out again. Then again.  Assemble said engine to your desired clearances with oil control mods, gasket to suit desired CR/Squish ect. Attach your extended sump with proper trap door oil baffles and head drain plumbed to sump with a SUMP BREATHER SYSTEM. Build your front diff with a decent LSD, rebuild your transfer case with a few extra plates, more than likely replace your tailshaft centre bearing and tighten up the rear diff. Tune to minimise excessive midrange cylinder pressure (timing unless you like to split bores and rebuild engines) Enjoy your engine, but hate the fact you are now destroying engine mounts, gearboxes, gearbox mounts, diff output flanges and driveshafts, diff mounts, tailshafts and front CV's.   Disclaimer.... Ive never done any of the aforementioned stuff.......
    • GTSBoy
      R32 GTS (RB20DE) Injectors Replacement

      By GTSBoy · Posted

      440s will support well over 400HP on petrol, which is a decent place to be for an RB20. 230+rwkW. Will be a safer bet for idle/low load. 550s would be nice for the extra headroom. I've made the same decision with mine (Neo25). 1000s are probably too big for the Nistuned ECU, so I have some smaller ones.
    • GTSBoy
      RB25DET Series 1 & Series 2 Gearbox Identification

      By GTSBoy · Posted

      thumbsup
    • AdiR34
      Did tie rods. Steering now not "springing" back.

      By AdiR34 · Posted

      Appreciate everything guys. I did go ahead and get an alignment... most of my complains are solved. Car is not perfect, but it's good enough. If I notice uneven tire wear or anything I'll just take everything back to stock.  Thanks again!
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      They still have not shipped the 550cc injectors as they weren't in stock, so in theory I could ask to get the 440cc ones instead, if those work better in my scenario. They're the same price so really shouldn't be an issue. Unfortunately I am not so knowledgeable in most parts of tuning so I wasn't sure what's best to choose between the two. 440cc ones are the lowest they have (not in stock, but available to buy nonetheless).
×
×
  • Create New...