Jump to content
SAU Community

Ac Temperature Issue

MightyV35
 Share

Recommended Posts

MightyV35 Contributor

MightyV35

Posted
Posted

Hi guys,

New to the forum. Picked up my first V35 350gt(2003 Coupe 6mt Bone stock) in Australia last week (Had an Infinity G35 in States). Absolutely love the car, mechanically it is immaculate, drive and shift smooth.

Today I notice an issue with Climate control. When i adjusted air con temperature from 18 to 28, i could barely feel any change, air was really cold all the time. Until i set it to 29, I could finally feel a bit difference. When i set it to 32, vents started blowing warm air but it was moderate. Also I notice that once AC is on, the compressor will not kick off, it stays on all the time unless ac off. I thought , compressor should switch on and off to adjust temperature.

Any thoughts? Please help, thank you!

Link to comment
https://www.sau.com.au/forums/topic/450604-ac-temperature-issue/
Share on other sites
sonicii Veteran

sonicii

Posted
Posted

These cars use a variable displacement compressor, they don't regulate temperature by turning the compressor on/off, the cooling power is adjusted by varying the compressor displacement. A bit like an inverter air conditioner for a house. So the compressor is always engaged when the AC is turned on.

That said, i have found most car ACs with climate control will turn on the AC compressor for at least the first 5 minutes after switching it on, regardless of the temperature setting. Probably for situations where you are using the AC to dry the air (defog windows) rather than just for cooling, usually the system will engage the heater at the same time.

Also keep in mind, CC systems usually have some 'smarts' built in, they monitor the external air temperature, and detect sunload, so they may blow cold air, even if the interior cabin temperature is at or below the current set point, in anticipation of the heating effects of outside air and sun. They don't wait for the cabin to get hot before reacting.

MightyV35 Contributor

MightyV35

Posted
  • Author
Posted

These cars use a variable displacement compressor, they don't regulate temperature by turning the compressor on/off, the cooling power is adjusted by varying the compressor displacement. A bit like an inverter air conditioner for a house. So the compressor is always engaged when the AC is turned on.

That said, i have found most car ACs with climate control will turn on the AC compressor for at least the first 5 minutes after switching it on, regardless of the temperature setting. Probably for situations where you are using the AC to dry the air (defog windows) rather than just for cooling, usually the system will engage the heater at the same time.

Also keep in mind, CC systems usually have some 'smarts' built in, they monitor the external air temperature, and detect sunload, so they may blow cold air, even if the interior cabin temperature is at or below the current set point, in anticipation of the heating effects of outside air and sun. They don't wait for the cabin to get hot before reacting.

Thanx for the response, Sonicii. Hummm, that's really interesting. anyway i did check the cabin air sensor underneath the steering wheel, it all hooked up. BTW, how do you monitor the reading from interior temp sensor?

sonicii Veteran

sonicii

Posted
Posted (edited)

I don't think you can in normal operation, but I believe you can go into the diag mode and see what temperature it is reading from the sensors.

I have attached the page from the FSM which may help.

atc.pdf

Edited by sonicii
MightyV35 Contributor

MightyV35

Posted
  • Author
Posted

I don't think you can in normal operation, but I believe you can go into the diag mode and see what temperature it is reading from the sensors.

I have attached the page from the FSM which may help.

Appreciated! Had a check, all three temperature sensors work fine.

MightyV35 Contributor

MightyV35

Posted
  • Author
Posted

I don't think you can in normal operation, but I believe you can go into the diag mode and see what temperature it is reading from the sensors.

I have attached the page from the FSM which may help.

Hi, I did check all three sensors again closely, when i ran test 2, it displayed 20 which i believe means all sensors are functional. But when i ran test 51, outside temperature sensor reading is 44(Actual temp is around 33), Cabin temp reading is around 36(Actual around 30 inside), MAF temp is around 26. Since outside temp is always displayed on center console, i found after a quick drive the out temp dropped from 44 to 34. However once I start the self diagnose again, the readings are inaccurate again. Is this means something wrong with the outside sensor and cabin sensor?

sonicii Veteran

sonicii

Posted
Posted

the outside sensor will be impacted by engine heat when you stop.. it is mounted in front of the radiator, which is why you see it drop fairly quickly once you start driving again.

Cabin temp sensor is near your left knee when in the driver seat, so you would need to ensure you are checking the temperature from around the same area.

It is unusual for these items to be inaccurate, normally when the sensor fails.. it fails properly..

chiefster1976 Apprentice

chiefster1976

Posted
Posted

This may not be your problem but worth a quick look!1

I had either really cold at 18 degrees but even on 18.5 onwards the temperature was blowing hot air... After further investigation

the sensor 2 pin connector under the steering wheel had bent one of the pins hence not working the sensor properly...

Check the connector pins and make sure they are not bent.... Once I reshaped my pins the climate worked fine!! Cheap fix..

worth a look hey!! good look....

No power to my AC at now at all. im stumped... ;-(

Good luck !!!!

MightyV35 Contributor

MightyV35

Posted
  • Author
Posted

This may not be your problem but worth a quick look!1

I had either really cold at 18 degrees but even on 18.5 onwards the temperature was blowing hot air... After further investigation

the sensor 2 pin connector under the steering wheel had bent one of the pins hence not working the sensor properly...

Check the connector pins and make sure they are not bent.... Once I reshaped my pins the climate worked fine!! Cheap fix..

worth a look hey!! good look....

No power to my AC at now at all. im stumped... ;-(

Good luck !!!!

Sorry to hear that your ac not work. Anyway thanx for the hint, I will look into it.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • joshuaho96
      Cas issue

      By joshuaho96 · Posted

      Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • joshuaho96
      Jacks that fit under GTR lips that can reach the subframe?

      By joshuaho96 · Posted

      On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      Nice....looking forward to that update
×
×
  • Create New...