Jump to content
SAU Community

Squealing Noise

camr33

By camr33,
in V Series (V35, V36, V37 & Infiniti)

 Share

Recommended Posts

camr33 Collaborator

camr33

Posted
Posted

Hi all,

I had my V35 coupe parked on the side of the road today, and when I started it up to drive off, I was met by an extremely loud screeching noise when I turned the wheel to the right and started to drive. It seems to be coming from the front, drivers side wheel arch.

After a 4-5 seconds, the squeal stopped. I drove forward for about 20m, then turned right onto another street when it squealed again- this time it was nowhere near as loud or long. I pulled back over and let the car idle for a minute, before taking off. It was only a 10 minute drive home, and it did not make the noise again.

Does anyone know what this could be? A few google searches indicate the power steering may be the culprit.

The power steering fluid is full to where it needs to be. The alignment seems to be fine. For the last few weeks, there has been a light clunk noise coming from the front right suspension (the car has tein coilovers), which I was going to get looked at after christmas. There don't seem to be any leaks from the car either. Usually when I reverse out of the drive, there is a slight buzz noise (presumably due to the EDFC) once I have started driving.

I purchased the car from a specialist importer, and am the first owner of the car in Australia. The car has just ticked over 80k kms (I have dereg papers and import papers etc to confirm this).

If anyone has any ideas, please let me know so I can contact the dealer with at least some knowledge of what the problem could be.

Link to comment
https://www.sau.com.au/forums/topic/451230-squealing-noise/
Share on other sites
camr33 Collaborator

camr33

Posted
  • Author
Posted

stone stuck between the brake rotor and caliper or caliper bracket..

Interesting...

I took it for a drive an hour or so ago and it didn't do it.

Hopefully it was just gremlins... I might get my phone ready when I go to work tomorrow and see if it does it again...

Link to comment
https://www.sau.com.au/forums/topic/451230-squealing-noise/#findComment-7434721
Share on other sites
Hertz Donut Proficient

Hertz Donut

Posted
Posted

I would say old/loose ancillary belts. They aren't expensive to replace, $70 for both from memory, and about 30 mins of your time.

+1. Commonly heard on old bangers but can happen on newer vehicles if the belt has been damaged or is getting dirty.

Link to comment
https://www.sau.com.au/forums/topic/451230-squealing-noise/#findComment-7434816
Share on other sites
camr33 Collaborator

camr33

Posted
  • Author
Posted

Just did a search and found these ones

http://www.kudosmotorsports.com/catalog/kudos-motorsports-ancillary-belt-set-belts-dayco-genuine-nissan-power-enterprise-nissan-350z-z33-skyline-v35-350gt-vq35de-p-1299.html

Would these be ok?

Thanks in advance.

Link to comment
https://www.sau.com.au/forums/topic/451230-squealing-noise/#findComment-7435700
Share on other sites
sonicii Veteran

sonicii

Posted
Posted

they should be ok, but these size belts are an 'off the shelf' item, you should be able to buy at just about any auto parts store.

Slipping belts often squeal when starting from cold and get loud when you rev the engine, and often go away after the first minute or so of driving. also can get louder when you put them under load, eg. power steering pump load (turning when not moving or moving slow) or AC compressor. Shouldn't really make much difference if you are turning right or left. and would also come from the front of the car, not the right side wheel arch.

Link to comment
https://www.sau.com.au/forums/topic/451230-squealing-noise/#findComment-7435943
Share on other sites
sonicii Veteran

sonicii

Posted
Posted

well sort of.. not really in the wheel arch... it is close enough to the front centre of the engine bay that it would sound like it is coming from under the bonnet when you are in the drivers seat.

when I had a faulty fuel damper, it sounded like it was coming from the engine bay, even thought it was the rear right side of the engine.

The sound of a squealing belt would also be quite a bit different to a rock in the calliper. a belt is a screech.. but a rock is more of a metallic scraping sound which is usually a bit modulated with wheel rotation speed.

Link to comment
https://www.sau.com.au/forums/topic/451230-squealing-noise/#findComment-7436027
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • perry_r33
      R34 GTR Vspec Garage Sale - All must go!

      By perry_r33 · Posted

      Pm sent 
    • Robot
      Skyline v36 350GT sedan hunting on idle

      By Robot · Posted

      Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...