Jump to content
SAU Community

Recommended Posts

recently converted my patrol to efi and had nothing but issues

its stumbling when revving off idle and poping through the intake I have replaced

fuel pump walbro 255lph in tank

spark plugs and gapped to 1.1

dizzy cap

afm

tps

aac valve

fpr

coolant temp sensor

intake manifold gaskets

put a kit through the injectors and replaced all the seals

timing is set to 15c btdc +2

every now and then it comes good

if I block my return line it revs normal

sometimes it decides to run rich for no reason

any ideas guys

Link to comment
https://www.sau.com.au/forums/topic/451438-rb30e-problems/
Share on other sites

Clean up or replace all the sensor plugs as they corrode and get bad connectivity.

My R31 has been doing this on and off for a while and I've replaced alot of the same things you have but I'm going to be replacing the CAS plug and Coolant temp sensor plug soon.

Get on R31 Skyline Club and you will find this is a VERY common problem with RB30's

Here --->> http://forum.r31skylineclub.com/index.php?board=7.0

Link to comment
https://www.sau.com.au/forums/topic/451438-rb30e-problems/#findComment-7438523
Share on other sites

cheers guys just replaced most of the connectors recently ive wired 12v to the coil no difference have noticed its heaps worse if I have no ait filter on the end of my afm if I block the intake partially with my hand it comes good its doing my head in lol

Link to comment
https://www.sau.com.au/forums/topic/451438-rb30e-problems/#findComment-7438612
Share on other sites

Could well be AFM. I'm looking into purchasing a newy or a Refurb as all of the three I have are 20+ years old and unknown condish.

Best I've found so far is a New aftermarket for $175+ post.

PM me if you want one. :thumbsup:

Link to comment
https://www.sau.com.au/forums/topic/451438-rb30e-problems/#findComment-7438621
Share on other sites

Could be dodge Earths or Loom related. The intake Backfire is supposedly a Lean issue, so any shortage of fuel or incorrect airflow signal could be to blame.

Airleaks, Fuel line Blockage / filter, injectors, so many things.

Have you read the ECU leds for Fault codes?

Link to comment
https://www.sau.com.au/forums/topic/451438-rb30e-problems/#findComment-7438657
Share on other sites

only codes I'm getting is a/c speed sensor and the one saying everything is working good I've changed all intake gaskets and hoses changes iac and gaskets to try fix the issues no change new fuel pump and fpr i can hear the pump pressurise and there is pressure in the line if i take it off i have only used the stock efi loom earths on the manifold but surely that should be plenty there straight to the battery i have removed the fuel filter there was no change I'm going to buy a new dizzy with cas,o2 sensor,leads see how that goes afar that everything has been changed except the air valve thing on the manifold near the thermostat and the ecu

Link to comment
https://www.sau.com.au/forums/topic/451438-rb30e-problems/#findComment-7438669
Share on other sites

The "Air Valve Thing" is the Air Regulator. That should really only do anything on Coldstart, as in, when you start it and let it idle, if the idle drops down after 30secs or so, it's working.

http://wiki.r31skylineclub.com/index.php?title=Air_Regulator

Link to comment
https://www.sau.com.au/forums/topic/451438-rb30e-problems/#findComment-7438680
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Cheers. Skyline is back on the menu, can’t get rid of it. It’s like a child you don’t want, or herpes 
    • I got back to Japan in January and was keen to get back on track as quickly as possible. Europe is god-awful for track accessibility (by comparison), so I picked up a first-gen GT86 in December just to have something I could jump into right away. The Skyline came over in a container this time and landed in early January. It was a bit battered after Europe, though—I refused to do anything beyond essential upkeep while it was over there. The clutch master cylinder gave out, and so did the power steering. I didn’t even bother changing the oil; it was the same stuff that went in just before I left Japan the first time. Naughty. Power steering parts would’ve cost double with shipping and taxes, so knowing I’d be heading back to Japan, I just postponed it and powered through the arm workout. It took a solid three months to get the car back on the road. Registration was a nightmare this time around. There were a bunch of BS fees to navigate, and sourcing parts was a headache. I needed stock seats for shaken, mistakenly blew 34k JPY on some ENR34 seats—which, of course, didn’t fit—then ended up having the car’s technical sheet amended to register it as a two-seater with the Brides. Then there’s the GT86. Amazing car. Does everything I want it to do. Parts are cheap, easy to find, and I don’t care what anyone says—it’s super rewarding to drive. I’ve done a few basic mods: diff ratio, coilovers, discs, pads, seat, etc. It already had a new exhaust manifold and the 180kph limiter removed, so I assume it’s running some kind of map. I’ve just been thrashing it at the track non-stop—mostly Fuji Speedway now, since I need something with higher speed after all that autobahn time. The wheels on the R34 always pissed me off—too big, and it was a nightmare getting tires to fit properly under the arches. So I threw in the towel and bought something that fits better. Looks way cleaner too (at least to me)—less hotboy, less attention-seeking. Still an R34, though. Now for future plans. There are a few things still outstanding with the car. First up, the rear subframe needs an overhaul—that’s priority one. Next, I need to figure out an engine rebuild plan. No timeline yet, but I want to keep it economical—not cutting corners, just not throwing tens of thousands at a mechanic I can barely communicate with. And finally, paint. Plus a bit of tidying up here and there.  
    • Nope, needed to clearance under the bar a little with a heat gun, a 1/2" extension as the "clearancer", and big hammer, I was aware of this from the onset, they fit a 2.0 with this intake no problems, but, the 2.5 is around 15mm taller than a 2.0, so "clearancing" was required  It "just" touched when test fitting, now, I have about 10mm of clearance  You cannot see where it was done, and so far, there's no contact when giving it the beans Happy days
    • It's been a while since I've updated this thread. The last year (and some) has been very hectic. In the second-half of 2024 I took the R34 on a trip through Germany, Italy, France and Switzerland - it was f*cking great. I got a little annoyed with the attention the car was getting around Europe and really didn't drive it that much. I could barely work on the car since I was living in an inner-city apartment (with underground parking). During the trip, the car lost power steering in France - split hose - and I ended up driving around 4,000kms with no power steering.  There were a few Nurburgring trips here and there, but in total the R34 amassed just shy of 7,000kms on European roads. Long story short, I broke up with the reason I was transferred to Europe for and requested to be moved back to Japan. The E90, loved it. It was a sunk cost of around EUR 10,000 and I sold it to a friend for EUR 1,500 just to get rid of it quickly. Trust me, moving countries f*cking sucks and I could not be bothered to be as methodical as I was the first time around.
×
×
  • Create New...