Jump to content
SAU Community

Bleeding Brakes With Endless Amounts Of Air Bubbles :/ (r33 Gtst)

deva0o
 Share

Recommended Posts

deva0o Community Regular

deva0o

Posted
Posted

Hey sau,

I'm having an issue while bleeding the brakes on my r33 gtst. I have gone through 3 bottles of dot 4 brake fluid already (system is now clear and no dirty fluid anymore). The method I'm using is a combo of the 2 man method and 1 man method with the brake bleeder kit you get with the small bottle etc. I've been using the 2 man method on the front calipers but for the rears I've been using the one man kit and can clearly see so many air bubbles coming out of the rear calipers down into the clear tube.

I haven't left the bmc to run dry, been careful to keep filling when getting low. The air bubbles won't stop. I'm about to go try the gravity bleed method and see what happens.

Things to note are that there wasn't any bubbles at all in the system until I had to change my front caliper mid way through the bleed as I accidentally cross threaded the bleeder nipple hole on my caliper so I swapped it over for another 33 gtst caliper in the garage, after that I've been having the issue with constant air bubbles and a spongy brake pedal that wont stiffen up at all... I thought that all those new air bubbles would disappear just as quick due to having to change a caliper over mid way and the loss of fluid etc would be causing it but I don't know anymore the bubbles on the rear calipers are endless and only started appearing after I changed the front caliper...

Anyone have a similar experience or any ideas? Also I've read different things about gravity bleeding and how people do it one by one or cracking all four nipples at the same time and just waiting.

Dose Pipe Sutututu Grand Master

Dose Pipe Sutututu

Posted
Posted

Does your car have ABS?

If so.. you may have air pockets in the ABS unit, just crack the top bleed points and do what you were doing before.. pedal down, open/close, pedal up.. then bleed the rears...

Once you're done, go on to a quiet area and when safe try to kick in ABS.. to get the pump going. Then back home and bleed some more, that should do the trick.

  • Like 1
deva0o Community Regular

deva0o

Posted
  • Author
Posted

Does your car have ABS?

If so.. you may have air pockets in the ABS unit, just crack the top bleed points and do what you were doing before.. pedal down, open/close, pedal up.. then bleed the rears...

Once you're done, go on to a quiet area and when safe try to kick in ABS.. to get the pump going. Then back home and bleed some more, that should do the trick.

Yes it does have ABS. I may try bleeding that then and see how I go. Thanks for the suggestion.

This may be abit of a silly question but the caliper I put on last night had a damaged piston dust boot so I removed a good one from a spare caliper and put it on the newer caliper. However another one next to it looks like it had a small split but I didn't replace that one. Was wondering how bad a little tiny split could be on a dust boot if anyone here knows? I may go back downstairs and change it just to be safe if suggested.

D.I.Y. Mik Veteran

D.I.Y. Mik

Posted
Posted

I had a problem with one of those suction bleeders. When you suck fluid, it leaks air past the nipple thread.

So i never could tell if it was done properly.

The two man method uses pressure and is the best way.

deva0o Community Regular

deva0o

Posted
  • Author
Posted

I had a problem with one of those suction bleeders. When you suck fluid, it leaks air past the nipple thread.

So i never could tell if it was done properly.

The two man method uses pressure and is the best way.

Yeah I'm going to try the 2 man method on the rear when I can get a helper tonight as I think it's the best way. Has anyone here tried the gravity method?

deva0o Community Regular

deva0o

Posted
  • Author
Posted

So abit of an update. Two man bled the brakes all around. No more air bubbles and pedal feels stiffer now. Haven't taken it for a drive but feels a lot different now... I think I will be chucking that one man bleeder kit in the bin.

75coupe Grand Master

75coupe

Posted
Posted

My one man brake bleed kit is a simple clear hose into a clean tin, hose goes from nipple over top arm and into tin, done cost $2 been using it for 8yrs... Never fails

warps Mentor

warps

Posted
Posted (edited)

Sounds like you may have found the problem.

To answer your earlier question, the dust boots have no bearing on the sealing of the piston. They just keep dust and moisture out, which protects the piston assembly from corroding and getting jammed. It's there for longevity of the caliper, rather than performing any sealing / operational function.

Edited by warps
deva0o Community Regular

deva0o

Posted
  • Author
Posted

Sounds like you may have found the problem.

To answer your earlier question, the dust boots have no bearing on the sealing of the piston. They just keep dust and moisture out, which protects the piston assembly from corroding and getting jammed. It's there for longevity of the caliper, rather than performing any sealing / operational function.

Cheers thanks for the info :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...