Jump to content
SAU Community

I Think I've Hit The Ignition Limit - What Are The Symptoms

Gareth87

By Gareth87,
in Engines & Forced Induction

 Share

Recommended Posts

Gareth87 Community Regular

Gareth87

Posted
Posted

Had my car on the dyno and as the power levels rose, we found it wasn't revving out to the set limiter.

Had the limiter at 8500 and on low boost it would hit a wall (sounded like a missfire) at 7500.

When we lifted the boost, it hit the missfire earlier at 6400rpm.

Tuner and I think it's pretty straight up and down ignition issue, however, there is some concern that it could be a trigger issue.. I run 1 coil with my distributor and standard FJ20 leads and It's making around 450hp.

Who's had ignition issues and what seems to happen?

I can convert to run 4x LS1 coils but it's going to be a pain in the arse wire in. I am considering an MSD 6A CDI to make sure it's that and not a trigger disc issue or something.

Looking forward to your thoughts,

G

Scott Black Rising Star

Scott Black

Posted
Posted (edited)

What coil are you using, as using one stock coil to fire 4 cylinders at 7000 rpm makes me think that there isn't enough time for the coil to reach saturation and there for weaker spark that's easier to fail to ignite at higher loads. So I'd say either replace the coil with one that needs less dwell for full saturation while still putting out a decent spark or yeah 4 ls coils. What ecu are you using and what sort of signal does the dizzy give, and what outputs does the ecu have as the ls coils with inbuilt ignitors are pretty simple to wire up in most cases, also I wouldn't think it's a trigger issue as if it was it wouldn't be affected as much by varying boost levels

Edited by Scott Black
Scott Black Rising Star

Scott Black

Posted
Posted

At 7000 rpm you have the coil firing 14000 times a minute or about 233 times a second, or about once every 4ms so that 4ms the coil needs to charge and fire( discharge). For peak performance a ls coil needs 5ms just for the charge. If you went to 4 coils even in wasted spark you still have 8ms so a decent amount of time for dwell, or sequential igniting giving you 16ms for dwell so heaps of time.

Gareth87 Community Regular

Gareth87

Posted
  • Author
Posted

Hi Scott, The coil I am using is an old Bosch coil. I'm not sure on the numbers. I tend to agree with you in regard to the spark issue, It certainly seems related to boost which I'm fairly sure is telling me it's a lack of spark when the coil has less time to reach saturation as you mentioned.

My concern with swapping to run 4x LS1 coils is that it requires new leads, wiring, different trigger disc etc.

Will an MSD CDI get me out of trouble and provide enough spark to get me to the rev limit?

Gareth87 Community Regular

Gareth87

Posted
  • Author
Posted

Just saw your calculations in the second post Scott, even if I do run an MSD with a single coil.. Does this mean the coil still needs that sort of time to recharge? which leaves me with the exact same problem.. or does the CDI system allow it to recharge faster? (I don't know a great deal about ignition systems yet)

Scott Black Rising Star

Scott Black

Posted
Posted

All coils need some time to charge, however some of the more powerful coils can still output a very powerful spark before there fully saturated so work better than a stock ignition system, it's what they use on old.gts that rev to 7k yet only use the one coil for 8 cylinders, weather that's enough with the higher cylinder pressure from forced induction I cant answer 100% because I'm used to using ls2 coils with wasted spark as minimum

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...