Jump to content
SAU Community

Recommended Posts

Hi all

I'm having an issue with my silver top RB20 intermittently not starting properly. If I turn the car on and it's dead cold it starts but if I turn it off straight away and try to start it again it sometimes wont start or even sound like it's close to starting. For it to start again it needs to left for several hours it seems.

The car has been sitting for the last 6 months however prior to that I've had no trouble with it starting in my 5 years of ownership.

At one point when it wasn't starting it ran out of fuel I think (dodgy fuel gauge) as the pump started making a loud noise. I've since filled it up so the fuel in it should all be fresh.

I also had an issue with the car running badly above 2000 rpm and swapped to a new AFM however this hasn't changed the starting issue at all.

If anyone has any suggestions that would be great as I'm at a real loss at what to do :(

Link to comment
https://www.sau.com.au/forums/topic/453454-rb20det-starting-issues/
Share on other sites

When this happens, try and unplug your water temp sensor on the coolant neck. It's the 2x wire one that goes to the ECU, see if that helps or unplug the AFM

It could be when your car is warm/warmer the cranking enrichment isn't enough to get the motor going.. it could be a mixture of things, dirty/faulty AFM, faulty FPR, dirty injectors, etc.

Changed the spark plugs today, while the car seems to run smoother now it didn't change the starting issue :(

I tired unplugging the wire on the coolant neck while it wasn't starting but that didn't make a difference.

I should mention that I've been turning the car on for max 30 seconds before turning it off and trying to start it so I don't think the problem is really heat related. That said if you leave it for a few hours and come back it will start first time.

How would a go about testing the fuel pump? And could that cause an issue with just start up?

Changed the spark plugs today, while the car seems to run smoother now it didn't change the starting issue :(

I tired unplugging the wire on the coolant neck while it wasn't starting but that didn't make a difference.

I should mention that I've been turning the car on for max 30 seconds before turning it off and trying to start it so I don't think the problem is really heat related. That said if you leave it for a few hours and come back it will start first time.

How would a go about testing the fuel pump? And could that cause an issue with just start up?

did you disconnect the coolant sensor for the ECU or the one for the dash? the ECU one has 2-wires not 1...

(not sure how related this is to you but here goes)

do you have access to a wideband o2?

back in the days when I knew nothing about cars (10+ yrs ago).. I had the same issue with my RB20DET, a mate that was doing engineering at uni suggested I hooked up his wideband. Ended up finding out the car was running lean in general when it was in vacuum, turned out my injectors were all clogged.

As soon as got all the injectors serviced, new o-rings put in the car started easily and idle was back to stoich.

Humour me a little and just try a mates battery

Don't use a jump pack or try jump it off another car

Connect direct to terminals

Ps. Every time you try to start it and it doesn't start your plugs get a bit dirtier and eventually fouled again.

Edited by Sinista32

Just tried a battery out of a car that gets driven every day, had slightly higher cca as well. Result was still the same though.

While it wasn't starting I also took the line off the fuel filter and primed the car and tons of fuel came out. I don't know know if that tells me if the pump is working fine though.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Agreed, I've never seen a 260RS specific manual. As GTSBoy said it will mostly be stagea other than the engine loom https://www.hgeconsulting.com.au/stageaservicemanual.pdf
    • You'lll likely have to make do with R33 GTR for engine/tranny stuff, and Stagea for the body. I don't know that there's even been an actual diagram seen in the wild.
    • Haha, i kow right? Could have bought so many cars for the same amount of money (or less) but driving Unicorn gives you at least +1mln to style 😅. Like wise man said "life's to short to drink cheap wine and drive boring cars" 😉
    • Newbie here, proud owner of an Autech 260RS. I'm on the hunt for wiring diagrams specific to the 260RS, particularly S1. I've ran my eyes through R33, R34 Diagrams, there are some similarities, however continue to find incorrect wire colours and pins on connectors in the 33,34 diagrams.   I was hoping someone could point me in the right direction? I'd be happy to pay for the originals in Japanese. I can translate them, at least they would be accurate.   Any help please would be greatly appreciated, never heard an RB26DETT before let alone driven one, and I've got a spaghetti monster of goodness to sort out.   Cheers Benny  
    • Hey all  im wondering if you can help me please I have put a rb20 box in my r34 gtt as my auto packed up and a friend had a spare box I know it’s not ideal but it will get me up and running for now. we have done the conversation and everything is working great but my Speedo we got a s13 speed sensor but my Speedo reads double now and I bought a speed converter but still not having any luck.  so I thought I’ll reach out and pick your brains  any help would be appreciated please as I wanna drive my car again 
×
×
  • Create New...