Jump to content
SAU Community

Recommended Posts

Dolphin front bar $912 plus shipping, taxes and charges. Maximum flow

03b72049f947ade8c7a7da7babff442a.jpg

Just too bad if you want to actually lower your car, that bar is huge!

Also a shame that dolphin uses fibreglass, fibreglass is ewww

One of the guys near me has a takero front bar and had to cut off the bottom of it and refibreglass it as it was so low. Aero is lyfe

Just go takeros lip on aero bar. Just adds little wing things to side to tie in with side skirts

My engine temps did not change from running the stock tiny intercooler to running an HDi kit.

Scotty's cooling mod, and a larger capacity radiator will improve the cooling system's ability to shed heat.

IMO; the OEM (quite noisy I agree) is far superior to thermo fans for heat management.

I've run a number of different setups using high capacity fans, and custom made shrouds to ensure efficiency, and nothing works better than the stock Clutch fan.

I did notice an improvement in cooling system performance when I changed from the stock "smiley face" front bar to the Aero Kit front bar.

i can't accurately compare the water temp between stock and HDi due to the outside temp and traffic condition may different.

for the cooling system, i have nismo thermostat, full alloy radiator, breath tank, Motul Mocool, just missing scotty's mod. i agree scotty's mod could stabilise water temp, but less effect when stuck in traffic on hot day? it is all good if my car is running above 30-40km/h all hot day, just problem when stop on idle, especially when aircon is on. if i go hardly even though at very low driving speed, then water temp will go down a bit. it seems the stock noisy fan or waterpump can't flow enough air/water when idle.

i can't accurately compare the water temp between stock and HDi due to the outside temp and traffic condition may different.

for the cooling system, i have nismo thermostat, full alloy radiator, breath tank, Motul Mocool, just missing scotty's mod. i agree scotty's mod could stabilise water temp, but less effect when stuck in traffic on hot day? it is all good if my car is running above 30-40km/h all hot day, just problem when stop on idle, especially when aircon is on. if i go hardly even though at very low driving speed, then water temp will go down a bit. it seems the stock noisy fan or waterpump can't flow enough air/water when idle.

Scotty's cooling mod lowers temps across the board, and allows cooling system to rapidly drop temp after any kind of load related cooling temp increase.

If you did nothing else to the cooling system; this mod would be the one I'd do first.

  • Like 1

Scotty's cooling mod lowers temps across the board, and allows cooling system to rapidly drop temp after any kind of load related cooling temp increase.

If you did nothing else to the cooling system; this mod would be the one I'd do first.

This will be one of my next mods. I need to do a cooling overhall with alloy radiatior and cooling mod etc

This will be one of my next mods. I need to do a cooling overhall with alloy radiatior and cooling mod etc

Talk to Scotty about the radiator; he now uses an OEM style replacement (alloy core/plastic tank) uprated core that is much easier to fit than the off the shelf all alloy units.

  • Like 1

Dolphin front bar $912 plus shipping, taxes and charges. Maximum flow

03b72049f947ade8c7a7da7babff442a.jpg

The Nismo front bar is 11ty billion times better looking than that abortion.

Shame about the head in the car... ;)

10838001_10153122897702217_6404291385902

I think the Dolphin front bar is priced 300% what it should be and it's actually quite ugly if you look close at it.

Heaps of hard edges, brake ducts way too big, exposing too much, hence the sign in the pic.

Looks tough but lacks sex.

Nismo kit beats it hands down.

For me the Axis Autech looks the best.

I really dig the bling of the Axis chrome grille.

It just brings that elegance this car deserves..

post-25026-0-19677200-1463471990_thumb.jpg

post-25026-0-96294300-1463472670_thumb.jpg

Edited by conan7772
  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...