Jump to content
SAU Community

Recommended Posts

sometimes, well most of the time i have it flat stick or slight throttle it bounces off the limiter and bogs down, missfires and slowly looses revs and power, its like what happens when your spark plug gap is ****ed...it was doing it with a gap of .8 then i went to a .7 but still does it. if i back off and back on the throttle it will sometimes get better but once it hits the limiter again itll bog down, missfire and loose revs even with foot flat or slightly, its like as if its surging out. this is mainly halfway through a slide (off street). all i want it to do is bounce off the limiter cleanly for peace at mind.

whats a solution? should i close or open gap more or is it something else? timing perhaps? i got no idea

cheers.

Link to comment
https://www.sau.com.au/forums/topic/45365-rb25det-off-limiter-bogging/
Share on other sites

The R34 will happily bounce off the rev limiter all day.

It used to be a slow pop pop pop as it hit limiter and then dropped spark then picked up again, but now with the light flywheel, its like a machine gun!

Nice.

Could be coils if it starts happening before you get to the limiter - mine starts misfiring at around 4500, and I don't usually see more than that because it feels terrible.

I understand that the car isn't running properly, but why do you want it to bounce off the limiter? If you're accelerating, hitting the limiter is costing you time, if you're doing a burnout, backing off the throttle a fraction should make bugger-all difference to smoke output, and if you're trying to drift, hitting the limiter generally means that you either have no throttle control or you're doing it wrong.

Learn throttle control - your car will thank you for it, and you'll be a better, quicker driver.

its not that i bounce it off the limiter often, its just the satisfaction that it will run cleanly if need be. all these people are sayin learn throttle control, learn throttle control, when clearly its not about that, i must explain a little better, as SOON as it hit the limiter, no bouncing off it, even without WOT, it still does it, sometimes doesnt even need to hit limiter, it just goes BRRRRR, looses revs and power and sometimes backfires hard. always when its under load.

sorry to confuse the subject but yea im not one of these 'lets just flatten it around a corner' style drivers.

  • 9 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Started sifting thru my brakes to decide which ones I will run on Clem   Made me think I should just put them all on Silver...for when brake fade just isn't an option   Should be able to bump rotor up from 343x32 to 348x36 off Supra. Not sure if the Supra annulus is right for the Alcons or APs but trying g to find a used Supra\M4 rotor to test fit The Alcons seem to gain 1-2mm clearance which all helps  
    • So car is getting a few mods to the cage and some jacking points welded in Meantime Ol Silver gets a new gearbox and shiny clutch.  Old Box is being set aside for Clem  
    • Probably speedometer itself if the odometer is ticking. If the needle is stuck from a bit of grease or something that can cause it to stay at 0. Or a cracked solder joint in the speedometer can do it too.
    • Thanks Fella’s   to take this off topic and to elaborate a bit more. I have an rb25/30 going into a r32 GTST.. expected to make around 600-700hp. Would you?   A) R34 GTT box   B) CD00#?  I’ve seen a few posts about the CD swap and sounds fairly involved with making it fit etc but if it’s worth the work then I’ll go that way
    • Lower at the hubs. Funny I forgot to mention that part. Do this pull here I turned the camera off too soon but the graph shows a drop at the top and that was because the pipe from the turbo blew off. The tuner said we could’ve made possibly another 15 whp. He also added if I switched to ethanol we could up the boost some more as well. I was comfortable capping it at the most of 20 pounds. Turns out the turbo pipe just needed a new worm clamp. Got home replaced that then did a third gear pull from 3k to 7200 rpm and the power was great to the top. I just got an ecu mounting bracket from IEE that I need to try and get everything to fit well. It’s a PITA to get the harness and ecu fit properly behind that kick plate 
×
×
  • Create New...