Jump to content
SAU Community

Recommended Posts

I have been trying to do this all morning with no luck. I have read how to enter diag. mode but my ecu does not have the selector screw, and also does not have the diag connector. Therefore i cannot enter diag mode.

I dont have any LEDs on the ecu either so i guess i go by the engine check light.

I have a 95mdl GTST, anyone else have this problem?

Link to comment
https://www.sau.com.au/forums/topic/45503-ecu-diagnostics/
Share on other sites

under the dash on the drivers side there is a connector with 14 pin holes (2 rows of 7 pin holes) in it....looking at the front of the connector with the chamfered end facing the left you need to switch the ignition on and touch the 6th and the 7th wires on the top row together for a second with a paperclip,the vehicle will enter diagnostic mode....

Link to comment
https://www.sau.com.au/forums/topic/45503-ecu-diagnostics/#findComment-928326
Share on other sites

mine didn't have the LED's but it did have the screw (94 model) where are you looking at the ecu? have you pulled it right out?

on this note i thought it good to mention that when i did mine it came up all good code 55.. but this happened even when i disconnected my injectors, CAS,AFM and water temp sensor.. so i dunno how helpful it is!!

Link to comment
https://www.sau.com.au/forums/topic/45503-ecu-diagnostics/#findComment-928600
Share on other sites

under the dash on the drivers side there is a connector with 14 pin holes (2 rows of 7 pin holes) in it....looking at the front of the connector with the chamfered end facing the left you need to switch the ignition on and touch the 6th and the 7th wires on the top row together for a second with a paperclip,the vehicle will enter diagnostic mode....

Thats the problem, there is no connector. Can anyone post a pic of where theirs is?

Link to comment
https://www.sau.com.au/forums/topic/45503-ecu-diagnostics/#findComment-928769
Share on other sites

mine didn't have the LED's but it did have the screw (94 model) where are you looking at the ecu? have you pulled it right out?

on this note i thought it good to mention that when i did mine it came up all good code 55.. but this happened even when i disconnected my injectors, CAS,AFM and water temp sensor.. so i dunno how helpful it is!!

Yeah i took the ecu right out and there were 2 holes, possibly where the LEDs go on the other models. Mine just had a blanking sticker over the holes.

Link to comment
https://www.sau.com.au/forums/topic/45503-ecu-diagnostics/#findComment-928774
Share on other sites

Where are you, i can get hold of a carmen scan tool, does all imports to current models and also displays active data.

Does the scan tool plug into the wiring harness or ecu or both? I would be interested in been shown what it does.

I am in quakers hill, about 25 mins from penrith

Link to comment
https://www.sau.com.au/forums/topic/45503-ecu-diagnostics/#findComment-928777
Share on other sites

sorry to hijack

but i wanted to get my ecu out to see if it is a stock one or not, cause it doesnt cut out at 180

can anyone help?

ive tried to get the kick panel out but after i take off two screws it is still connected by something else behind it

Mine only had the 1 screw closest to the front near the firewall but has 2 clips that need a good tug to break free. get a commone screwdriver and wedge it between the panel at the back of it, near the door seal.

Link to comment
https://www.sau.com.au/forums/topic/45503-ecu-diagnostics/#findComment-928779
Share on other sites

i had to lift of the plastic sill (with skyline embossed) then unscrew that plastic nut near the firewall

then i unscrewed one of the dash compartment screws so that i could get it out a bit easier

once i done that it still has a clip of some sort that needs to be undone or something, im guessing that is what needs a good tug?

Link to comment
https://www.sau.com.au/forums/topic/45503-ecu-diagnostics/#findComment-928786
Share on other sites

Jason, they ECU has 3 bolts holding it in, one on firewall and two on other end!

Damo, mine has a clear platic sticker with Jap writing over the screw.. it's within the hole and needs a small flat head screw driver! if it has no LED's then just turn clockwise all the way the turn it back!

Link to comment
https://www.sau.com.au/forums/topic/45503-ecu-diagnostics/#findComment-929282
Share on other sites

mine didn't have the LED's but it did have the screw (94 model) where are you looking at the ecu? have you pulled it right out?

on this note i thought it good to mention that when i did mine it came up all good code 55.. but this happened even when i disconnected my injectors, CAS,AFM and water temp sensor.. so i dunno how helpful it is!!

The engine needs to be running. Disconnect Water Temp sender with engine running, then run diagnostics.
Link to comment
https://www.sau.com.au/forums/topic/45503-ecu-diagnostics/#findComment-930091
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah i found that alot of parts can be wrong or "very" hard to get the real right one. I already bought some brakes years ago on me "old" GT calipers and they were wrong too 😄  I told them too. Even send them pictures...but they said "EBC catalogue has them on my car... So i dont know what their answer will be. I call monday them and let them know that they are really not on my car. If they were they would be already on a car...
    • Welcome to Skyline ownership. Yes, it is entirely possible parts websites get things wrong. There's a whole world of inaccuracies out there when it comes to R34 stuff (and probably 33 and 32). Lots of things that are 'just bolt on, entirely interchangable' aren't. Even between S1 and S2 R34's. Yes they have a GTT item supposedly being 296mm. This is incorrect. I would call whoever you got them from and return them and let them know the GTT actually uses 310mm rotors. Depending on where you got them from your experience and success will obviously vary.
    • Hi...a bit a "development" on the brakes. I spoke to the guys where i get brakes from...and they are saying that 296mm EBC are for R34 GT-T. I then went to their site: https://www.ebcbrakes.com/vehicle/uk-row/NISSAN/Skyline (R34)/ and search for my car(R34 GT 1998 - it has GTT brakes) and it show me this USR1229 number and they are rly 296mm rotors... So now iam rly confused... The rotors i have now on the car are 310mm asi shown... So where is the problem? Does the whole EBC got it wrong or my calipers are just...idk know what?  
    • Oh What the hell, I used to get a "are you sure you want to reply, this thread is XX months old" message. Maybe a software update remove that. My bad.
    • This is a recipe for disaster* Note: Disaster is relative. The thing that often gets lost in threads like this is what is considered acceptable poke and compromise between what one person considers 'good' looks and what someone else does. The quoted specs would sit absurdly outside the guards with the spacers mentioned and need  REALLY thin tyres and a LOT of camber AND rolling the guards to fit. Some people love this. Some people consider this a ruined car. One thing is for certain though, rolling the guards is pretty much mandatory for any 'good' fitment (of either variety). It is often the difference between any fitment remotely close to the guards. "Not to mention the rears were like a mm from hitting the coilovers." I have a question though - This spec is VERY close to what I was planning to buy relative to the inboard suspension - I have an offset measuring tool on the way to confirm it. When you say "like a mm" do you mean literally 1mm? Or 2mm? Cause that's enough clearance for me in the rear :p I actually found the more limiting factor ISNT the coilover but the actual suspension arms. Did you take a look at how close those were?
×
×
  • Create New...