Jump to content
SAU Community

Temp Job Thread

GTR-N1

By GTR-N1,
in New South Wales

 Share

Recommended Posts

Brick Mentor

Brick

Posted
Posted (edited)

Signwriter required at Penrith to do a 1m x 3m sign for me. Payment will be immediate after the job is done. With thanks Tez.

Hi Terry, aleks (FishingFreak in the stagea section) has a sign writing company based in St marys. He will look after you. Edited by Brick
Link to comment
https://www.sau.com.au/forums/topic/455541-temp-job-thread/#findComment-7514148
Share on other sites
Daleo Grand Master

Daleo

Posted
Posted

Good stuff Terry, we found him very reasonable, and gave good advice which saved us a decent bit of cash when we bought our gas hot water service.

He also came out on really short notice to unblock a drain, and didn't hit us with a callout charge because we'd used him before.

I'll always recommend guys like that.

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/455541-temp-job-thread/#findComment-7522371
Share on other sites
  • 1 month later...
GTR-N1 Grand Master

GTR-N1

Posted
  • Author
Posted

FishingFreak aka Aleks did a great Signwriting job for me thanks.

"Graphics and Print" - Recommended.

Next paying job is for a S/S weld of a Nismo muffler to the pipe.

Up to it Dale?

It pains me to say this but the muffler coming off is near new too!

HKS Silent Power one.

Link to comment
https://www.sau.com.au/forums/topic/455541-temp-job-thread/#findComment-7551754
Share on other sites
Daleo Grand Master

Daleo

Posted
Posted

FishingFreak aka Aleks did a great Signwriting job for me thanks.

"Graphics and Print" - Recommended.

Next paying job is for a S/S weld of a Nismo muffler to the pipe.

Up to it Dale?

It pains me to say this but the muffler coming off is near new too!

HKS Silent Power one.

I only just saw this!

Let me know when you have some time Terry; I'm happy to have a look. I can purge as well for a neat internal surface.

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/455541-temp-job-thread/#findComment-7553515
Share on other sites
  • 1 month later...
  • 10 months later...
Daleo Grand Master

Daleo

Posted
Posted

Tomorrow free?

Would anyone have a free day 6am to 8pm tomorrow to help me check a car and (all going well), tow it back (on a UHaul trailer) to Blacktown?

Payment can be discussed on PM. Ta. Grateful.

I'm not available tomorrow, but happy to help on Friday if that works at all Terry?

Link to comment
https://www.sau.com.au/forums/topic/455541-temp-job-thread/#findComment-7744940
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Predator1
      FS - RB30 Turbo upgrade bolton turbo kit - 600kw

      By Predator1 · Posted

      Details: Turbo Borg Warner EFR 9180 with 1.05 rear housing Upgraded TurboSmart integrated BOV Sanded and powdercoated compressor cover in gloss black Elbow welded with wiggins clamp Speed Sensor(Not included) (Can include oil drain(heat wrapped + titanium intake pipe with almost new filter for a tad extra). Manifold: 6 Boost RB26/30 twin scroll manifold  e-MAP ports drilled into both scrolls(I was using the TAARKS EMAP KIT) Turbo is in excellent condition. Always used Penrite 15w50 Racing oil(Changed less then 2000ks). Also using the Turbosmart OP regulator and filter. Downpipe: 4inch Stainless steel with VBand inlet and outlet clamps(included) Heat wrapped Dual ports for Dyno/Wideband usage Will throw in free 2.5 inch intercooler pipe(2.5inch From turbo outlet to 3.5 inch intercooler) - Powder coated black. Turbo made 563rwkw on mainline hub dyno at around 24-25psi boost - Pump fuel. Will def make over 600kw on e85. Didn't bother as my e-MAP was through the roof with my setup sitting past the choke line. I have a cnc ported and fully built head on my 3.2. Turbine speed saw max of around 109k rpm. I'm running this on my R32 GTR, with AC, and the original power steering pump. The manifold clears the AC lines, ABS, and everything else. Although I had new AC lines because I just wanted new ones and I heat wrapped them as well. This will make more power on a slightly lower capacity motor with a higher PR. And I have since upgraded to a G45-1500. Have pics and videos if need be.  Absolutely nothing wrong with setup. Turbo is in perfect condition. No shaft play or oil leaks at all. All the work was professionally done. The transient response of this is fkn amazing. I cannot rave more about this turbo. If I wasn't chasing 4 figures, I would have kept it. $5000 NZ. Located: Auckland, New Zealand.    
    • PranK
      ATCC Amaroo Park 1987

      By PranK · Posted

      I particularly like the look of the John Player Special team. (Thumbnail isn't different but hit play for the clip)  
    • PranK
      ATCC Amaroo Park 1987

      By PranK · Posted

      Such a cool collection of cars back then.  
    • PotatoCake
      R33 nismo cluster

      By PotatoCake · Posted

      Mystery solved, thanks bro Bit of a strange mix, but i dont mind it, still looks good. 
    • V35_Paul
      Who has a Infiniti Q60, Q50 (V37)?

      By V35_Paul · Posted

      nah no problems with bearings or hubs.  just the water pump leak and my AC death
×
×
  • Create New...