Jump to content
SAU Community

Tyre Pressure Monitoring System By Schrader Airaware

hotz
 Share

Recommended Posts

hotz Proficient

hotz

Posted
Posted

I've had this TPMS for about more than two years, brand new, never fitted. Just opened the wrap for inspection. Everything intact in the box.

It was probably b/t $280-$300 when bought. I'll let it go for $220 + postage.

post-88178-0-27520100-1428789731_thumb.jpg

post-88178-0-84133100-1428789801_thumb.jpg

post-88178-0-17872700-1428789917_thumb.jpg

  • 2 weeks later...
hotz Proficient

hotz

Posted
  • Author
Posted

I'll do 200 + postage. I can not go any lower.

As I said, it is brand new and I unwrapped the box to check it out on the day I posted this ad. I have not even turned it on.

hotz Proficient

hotz

Posted
  • Author
Posted

The first picture shows the monitor w/ the start-up lights right after I started it.

The second one shows when the monitor is settled. But I think it needs programming in order to monitor the desirable pressures in the tyres you select.

hotz Proficient

hotz

Posted
  • Author
Posted

No worries!

Yes, it has all the booklets you need for how to work it. Even It has a quick reference to throw in the glove box. See picture shown above when I started this post.

Gts-t Grand Master

Gts-t

Posted
Posted

Just a fyi

The pressure sensors usually dont atart transmitting until they see some pressure. So not untill they are installed in a wheel with a tyre on it and pumped up above a certain psi. It is to preserve the battery life of the sensors

  • 2 weeks later...
  • 2 months later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • funkymonkey
      Jacks that fit under GTR lips that can reach the subframe?

      By funkymonkey · Posted

      I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      ..this is the current state of that port. I appreciate the info help (and the link to the Earls thing @Duncan). Though going by that it seems like 1/4 then BSP'ing it and using a bush may work. I don't know where I'd be remote mounting the pressure sender... to... exactly. I assume the idea here is that any vibration is taken up by the semiflexible/flexible hose itself instead of it leveraging against the block directly. I want to believe a stronger, steel bush/adapter would work, but I don't know if that is engineeringly sound or just wishful thinking given the stupendous implications of a leak/failure in this spot. What are the real world risks of dissimilar metals here? It's a 6061 Aluminum block, and I'm talking brass or steel or SS adapters/things.
×
×
  • Create New...