Jump to content
SAU Community

Recommended Posts


All good till the government rips the ass out of what you have earned from busting your balls. Wow look at, oh, bummer.


Yep always paying the man

I've made 10-11k a fortnight plenty of times when they offer unlimited overtime but I think from memory I only end up with 6k


I feel you on the mega overtime. have done some 26-28 hour days. Get home, pass out on the couch for a few hours and then wake up for some dinner. Far from a good time.


That's the go, getting work to pay 26-28hours for a 24hr day
  • Like 1
Any updates?



It has been quoted, assessor to review then I will have an answer, it seems like it's repairable, we have discussed our tidy up [emoji14] the 34 will be very tidy after this I'm sure [emoji6]

We have a couple of ideas that if we go ahead with will really set the car apart from others [emoji108]
  • Like 2



It has been quoted, assessor to review then I will have an answer, it seems like it's repairable, we have discussed our tidy up [emoji14] the 34 will be very tidy after this I'm sure [emoji6]

We have a couple of ideas that if we go ahead with will really set the car apart from others [emoji108]



Suicide doors and 24" mags?
  • Like 2
13 hours ago, shoey85 said:

 

 


It has been quoted, assessor to review then I will have an answer, it seems like it's repairable, we have discussed our tidy up emoji14.png the 34 will be very tidy after this I'm sure emoji6.png

We have a couple of ideas that if we go ahead with will really set the car apart from others emoji108.png

 

 

Ooooo sounds promising 

Was thinking of strengthening the front a little and running a new cai

5F021C56-AA04-40BE-AE4F-270AAE88264A-1514-0000019928DF801A.jpg.b41678dceae543f796def36451ce8707.jpg


That will make it 2 of a kind then.

Fully equipped to bash roos and do water crossings. Traction and water ingress might be an issue you want to look into though.



  • Similar Content

  • Latest Posts

    • Did and sync timing with light 
    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
×
×
  • Create New...