Jump to content
SAU Community

Recommended Posts

Hey guys so i recently fitted a bride euro2 seat and a bride rail into the passenger side of my r34 gtt.

The rail that suits a euro2 is a Bride MO type. I have a RO type with the MO conversion plates fitted to make it suit the Euro2 seat shown in the link bellow:

http://www.nengun.com/bride/mo-adapters

The seat position is now at least 2cm higher than the stock seat making it feel like a bus.

Is there any other rails that sit lower, or any other way to position the seat lower?

last resort id go would be fabricators cutting the rail up!!

You literally need every little bit you can to get the seat down low, especially on the passenger side. Any adapter will make you sit on the roof. Only 2 options would be get just the MO type rail (check it out to see what it looks like first too, as it may still sit you kind of high). Or, get one fabbed, which is what I did with my Gias II's, and it now sits lower than standard seats.

You literally need every little bit you can to get the seat down low, especially on the passenger side. Any adapter will make you sit on the roof. Only 2 options would be get just the MO type rail (check it out to see what it looks like first too, as it may still sit you kind of high). Or, get one fabbed, which is what I did with my Gias II's, and it now sits lower than standard seats.

i was told the RO and MO are similar in height :(

who fabricated your rail? and how much did u pay if u dont mind me asking? :)

i was told the RO and MO are similar in height :(

who fabricated your rail? and how much did u pay if u dont mind me asking? :)

They look like they would yeah. Actually fabbed it myself. So just the cost of some 3 mm flat bar in mild steel.

Shoijiki, was that fab from scratch or a modded bride rail to sit lower?

Modified Chinese universal rail. It was to "suit" R34 GT-T, and it did bolt in! However your head would touch the roof essentially! So all the flanges were cut off and the frame trimmed down and re-welded to sit as low as is possible without modifying the floor pan. The passenger side cannot sit as low as the drivers side since the floor has a large bulge in the RH rear area. However it's still much lower than stock with the Gias seats. Also I extended the seat belt bracket on the rail to be 5 cm higher too, as it feels like its too far down on the Bride/Uni Rails.

I can show you some quick snaps of the modded rails if you like.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Oh, also, forgot to add these photos I believe.
    • Thought i'd update on this. I was able to get in contact with Craig Lieberman and later on Darryl Alison (owner of Kaizo Industries). Darryl was able to help me verify that my car was in fact one of theirs and is helping me find more info on mine !
    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
×
×
  • Create New...