Jump to content
SAU Community

Recommended Posts

Parts for Sale

Located In Ballarat VIC

Will post most parts at Buyers expense

Open to offers

****RB30 Parts****

R31 Auto Gearbox Computer (Located under passenger seat)
-A64-000 J29 $5
-A64-000 J41 x2 $5

Charcoal Canister $20
Power steering Res $20
O2 Sensor x2 $20 each
Idle Air adjust with FICD $20
Pressure Reg – Solenoid Valve $20
Auto Throttle Position Sensor $5
Air Reg x2 $10 each
Factory Water inlet and out block fittings (Rad hoses connect to) $5 each
CAS(Crank Angle Sensor) x2 $10 each
Coils x4 $10 each
Pressure Reg $10
Throttle body x2 1Missing the Throttle cable connector $10 each
Dizzy x2 $20 Each
Throttle cable holder Block bracket $5
Starter Motor x2 $25 each
Alternator $25
Fuel Pump out of Cradle $20

****Outside Parts****

Chrome Door Handles – All Except Drivers Side $40
Black Door Handle – Front Passenger side $10
Bonnet Hinges Both Left and right $5 each
Fuel Cap $5
S3 Headlight Drivers Side $25
S3 Headlight Passenger side x3 $25 each
Front Bar Indicators – Both sides $10
Chrome Strips that go above the top of the doors – both sides $30
Side Indicators – Both sides $10
Wagon Drivers Side Tail light $10
Wagon Passenger Side Tail light – Small Crack $5
S3 Filler bar x2 $10 each
S2 Filler Bar $10
S2 Passenger Gaurd $20
S3 Passenger and Drivers Side Gaurds $20 each
S3 Front Bar $50
S3 Rear Bar $50
Stock sway bar $10

****Interior Parts****

Ash tray - $5
6 Gauge Cluster x2 $30 each
Pintara cluster (Clock where the rev gauge is) $10
Random Brown interior – Too much to list – Let me know what you after
Random grey dash buttons - Let me know what you after
Grey dash - $20
Brown Dash insert S3 TI (The whole thing the dash sits in) $50
Indicator/Headlight stork x3 $20 each
Wiper stork 1x Adjuster $20 x1 Non Adjuster $10

Link to comment
https://www.sau.com.au/forums/topic/456919-vic-r31-skyline-rb30-parts/
Share on other sites

  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
    • I thought the same to start with. But then I thought it was one of those LCAs where the end of the ARB goes through a bushing in the LCA itself, instead of having an end link.
×
×
  • Create New...