Jump to content
SAU Community

Recommended Posts

So i've been having having problems with the car going into limp mode intermittently for a couple of months, some days its really bad and sometimes it wont do it for a week at a time.

My mrs drives it mainly, -taking kids to school etc and its really starting to shit her, and thus it impacts on me.

Since it started happening i've swapped out the pedal tps, the throttle body, (both with known working ones) put a new battery in and wiggled and unplugged shit etc, dit the pedal poition and throttle body relearn stuff, but still get the same problem.

I've searched a lot and it seems to be a common problem but had anyone found a definitive fix?

Oh yeah I've also cleared the drain hole under the battery and dried out all the stuff, (fuse box etc around there)

-Rod

Link to comment
https://www.sau.com.au/forums/topic/457051-m35-stagea-p0121-throttle-problem/
Share on other sites

So you have a TPS fault, something is wrong with the tps signal back to the ecu. There are two tps signals and they are both monitored/compared by the ecu constantly and anything that may throw the voltages out, even slightly will trigger the limp mode.

Do you have anything else hanging off the TPS wires? Such as a cruise control, piggyback ecu or something else aftermarket?

Yeah I punched out the drain tube.

However the error occurred 3 times again today.

After being good for a few days. I don't know what to do now!

I've got a whole other car for parts so I might just keep swapping things. Starting with that whole fuse box, and maybe the ecu.

My mrs said it seems to rev up more than it should just before it throws the error. And it's always after stopping at an intersection or something and when she gets back on the accelerator it does it.

It sounds like a problem with the throttle potentiometer going high or low just off closed but it's been swapped with one from the other car that was fine

Plenty of times, either the throttle resistor on the back of the pedal, or the throttle itself is likely the issue, unless you have a wiring fault between them and the ecu.

What codes are the ecu throwing? Is it only the P0121? That seems to relate to the pedal sensor.

When the throttle goes into limp mode it almost disables the throttle. It will sit on 1200 revs, enough to drive out of problems and get off the road. You can actually get more throttle out of it if you push the pedal all the way to the floor, but it is quite dangerous, especially as it happens randomly.

Yeah that's the only code, and having tried the pedal assembly and throttle body from the other car that never had a problem I'm suspecting a wiring issue, corrosion, dry joint, or ecu problem, I'll swap the ecu and fuse box out over the weekend and pray that fixes it. It was strange that it worked flawlessly for 3 days after changing the relay so maybe there is a wiring problem in the fuse box.

What locally sold car has the same throttle pot? I vaguely remember reading it was a Maxima but can't find it again...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...