Jump to content
SAU Community

Recommended Posts

So i've been having having problems with the car going into limp mode intermittently for a couple of months, some days its really bad and sometimes it wont do it for a week at a time.

My mrs drives it mainly, -taking kids to school etc and its really starting to shit her, and thus it impacts on me.

Since it started happening i've swapped out the pedal tps, the throttle body, (both with known working ones) put a new battery in and wiggled and unplugged shit etc, dit the pedal poition and throttle body relearn stuff, but still get the same problem.

I've searched a lot and it seems to be a common problem but had anyone found a definitive fix?

Oh yeah I've also cleared the drain hole under the battery and dried out all the stuff, (fuse box etc around there)

-Rod

Link to comment
https://www.sau.com.au/forums/topic/457051-m35-stagea-p0121-throttle-problem/
Share on other sites

So you have a TPS fault, something is wrong with the tps signal back to the ecu. There are two tps signals and they are both monitored/compared by the ecu constantly and anything that may throw the voltages out, even slightly will trigger the limp mode.

Do you have anything else hanging off the TPS wires? Such as a cruise control, piggyback ecu or something else aftermarket?

Yeah I punched out the drain tube.

However the error occurred 3 times again today.

After being good for a few days. I don't know what to do now!

I've got a whole other car for parts so I might just keep swapping things. Starting with that whole fuse box, and maybe the ecu.

My mrs said it seems to rev up more than it should just before it throws the error. And it's always after stopping at an intersection or something and when she gets back on the accelerator it does it.

It sounds like a problem with the throttle potentiometer going high or low just off closed but it's been swapped with one from the other car that was fine

Plenty of times, either the throttle resistor on the back of the pedal, or the throttle itself is likely the issue, unless you have a wiring fault between them and the ecu.

What codes are the ecu throwing? Is it only the P0121? That seems to relate to the pedal sensor.

When the throttle goes into limp mode it almost disables the throttle. It will sit on 1200 revs, enough to drive out of problems and get off the road. You can actually get more throttle out of it if you push the pedal all the way to the floor, but it is quite dangerous, especially as it happens randomly.

Yeah that's the only code, and having tried the pedal assembly and throttle body from the other car that never had a problem I'm suspecting a wiring issue, corrosion, dry joint, or ecu problem, I'll swap the ecu and fuse box out over the weekend and pray that fixes it. It was strange that it worked flawlessly for 3 days after changing the relay so maybe there is a wiring problem in the fuse box.

What locally sold car has the same throttle pot? I vaguely remember reading it was a Maxima but can't find it again...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok thanks..that was my second question if i can somehow bypass this even with Nistune(that is all i have right now...aparat from stock ECU. So with some aftemarket it can by "bypassed" or make it work?  I know there is Link or Haltech (mainly used). We have ECUmaster here so i will gather some info about it.
    • Yes. You will need to get the original boost sensor and wire it in. That is.... if you plan to use a stock ECU - even a Nistuned ECU. The Nissan ECU will not operate correctly without it connected. And yes, it will do annoying stuff like you are experiencing. You will almost certainly be better off with some aftermarket ECU, than trying to hunt down rare sensors.
    • Ok so ABS/TCS is "not" the problem. Yeah i know now about the ABS with Nistune(i told that to the Nistune guy) but iam not 100% why or why i dont have ABS. ABS cube is in the engine (always has been) but i had braked couple of times rly hard and brakes just locked and scream. Does all Skylines have ABS cube? That boost sensor https://www.sau.com.au/forums/topic/367633-wtb-r34-gtt-turbo-pressure-sensor-pics-inside/ Is this it? I need to ask but i have a picture of engine bay and i do not see that (100% is not in that place) If i do not have this the car can do what mine is?(cutting around 4000 rpm) Here is the pic of my engine bay(only one i have) BUT i think i dont have that cuz loom was used from my RB20DE NEO and i know (obviously) that it does not have boost control or any wire to that...) so maybe that is the problem? (i dont know for 100% if that car where the engine is from had that)...but i dont have the loom from that
    • I'm with you here. It's either loom has an issue, OR, injectors are not functioning properly. It could even be they're just constantly dribbling, hence the wet, but not firing.
    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
×
×
  • Create New...