Jump to content
SAU Community

Recommended Posts

these are the parts that i have left no reasonable offer denied

rear bar grey in colour bit faded $40

reinforcement behind rear bar $15

front seats out of m spec immac $300

rear seats out of m spec $90

grey carpet $40

grey hoodlining $30

fuel tank with fuel pump and sender $50

rear window $100

left hand quarter window with rubber $50

rear sub frame with hubs & control arms SOLD

gts4 or gtr front hubs control arms and struts $80

ac compressor $40

manual tail shaft $40

all plastics from center console and radio facia

brake master cyl with pipes and abs unit $100

A PILLAR TRIMS $25 EACH

LH POWER MIRROR $40

complete top end rb20det head, manifolds, turbo wiring, computer asking $400

no gearbox

no coils or ignitor

no dash or vents

Link to comment
https://www.sau.com.au/forums/topic/45748-wrecking-r32/
Share on other sites

is the boot charcoal metalic or gray as described???

Also do you have the metal lining that goes around the rear windo its a three piece metal strip thing???? PM me your mobile and i can have a chat about some stuff and prices!!!

Link to comment
https://www.sau.com.au/forums/topic/45748-wrecking-r32/#findComment-931254
Share on other sites

Need 2 x o2 sensors out of GTR r32 , the ones that scew into dumps , must be working please.

these are the parts that i have left no reasonable offer denied

boot lid imac with wing off m spec gray in colour $90

rear bar grey in colour bit faded $30

rear seats out of m spec $90

both doors with all internals and glass . no door trims $200

grey carpet $40

grey hoodlining $30

fuel tank with fuel pump and sender $50

rear window $100

rear sub frame with hubs & control arms $80

gts4 or gtr front hubs control arms and struts $80

ac compressor $40

manual tail shaft $40

complete top end rb20det head, manifolds, turbo wiring, computer asking $400

no gearbox

no coils or ignitor

no dash or vents

Link to comment
https://www.sau.com.au/forums/topic/45748-wrecking-r32/#findComment-931497
Share on other sites

these are the parts that i have left no reasonable offer denied

no gearbox

no coils or ignitor

no dash or vents

What about the underbody plastic bit RHF Guard - protects the BOV are from road dirt?

Odd screws/connectors from the bumper etc?

R32 GTR not sure if other cars are different

Link to comment
https://www.sau.com.au/forums/topic/45748-wrecking-r32/#findComment-934827
Share on other sites

Hey man if you know if the R32 drivers side window is the same as an R33 and in good condition send pic if possible i'll take it plus its internals $130 and i'll front the shipping.

PM me. thanks

i'd say it would be different

Link to comment
https://www.sau.com.au/forums/topic/45748-wrecking-r32/#findComment-939147
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I hadn't thought about the variable power steering assist. Presumably, it will always be the same level of assist as you get in an S14. The R32/3/4 are either helliishly heavy (at low speeds) if the solenoid is not powered at all, or hellishly too light (at high speed) if it is powered all the time. I presume that it is PWM controlled on those cars. I hadn't thought about the S cars not having variable assist. ugh. What crappy plebby cars they must be!  
    • Hmm yeah that is a good point. It looks like it'll just bolt in with no real issue besides maybe the bushings being different. My other concern was that 2 pin plug that I assume is used in some way to control the rack solenoid depending on the speed signal from the ecu. The DMAX rack doesn't even have that plug though so, don't think it'll matter. Might just order the rack and see how it goes. Will update this when I figure something out
    • I'd say it's a fair bet that the feed and return fluid lines will be in different enough spots that you would need to come up with a way to cut the originals short and adapt with new hard line adaption or braided teflon hoses or somesuch. But really, you have the car, you have the photos of the DMAX rack - you should be able to go out there and see for yourself whether they're in the same or different spots.
    • I've been doing some looking around and honestly was just considering throwing a new rack at it. I saw that the dmax silvia rack bolts up into the 33 with the silvia bushings but not sure if the high pressure lines will sit in the correct spot. I believe other version of the 33 rack are the same/similar to the racks that can be opened up without as much fuss so I assume the dmax rack would fit but any ideas?
    • I've never played with one, but I would expect that you are correct. That slot looks like it is intended to be used to unscrew the end, and the flats on the body would be better than grabbing it around the round bit with a pipe wrench. So, yeah, probably unscrews. You'll probably have to make a tool to drive in that slot.
×
×
  • Create New...