Jump to content
SAU Community

Rb26/30 Lifting Head Need Help

James_03

By James_03,
in Engines & Forced Induction

 Share

Recommended Posts

luke gtr Grand Master

luke gtr

Posted
Posted

Mine didn't.

Ran fine until I spun bearings.

and I'll be looking at better quality than a bunnigs washer.

going to the local bolt master to see if the have any high tensile washers in double thickness.

luke gtr Grand Master

luke gtr

Posted
Posted

Seems odd how some people have this issue and others don't. Any idea if your block came from an R31 or a VL?

thought about this.

Depending on block machining, head machining, and gasket thickness used, will depend if they just clear, or just foul.

the more you skim off, and thinner the gasket, the more likely to need the extra washer.

  • Like 1
steve200b Proficient

steve200b

Posted
Posted

Seems odd how some people have this issue and others don't. Any idea if your block came from an R31 or a VL?

I have a r31 series 3 block and had 2mm skimmed of the 25 head and using 1 washer holding 21psi with no issue

  • 4 weeks later...
James_03 Mentor

James_03

Posted
  • Author
Posted

Thought I would report back guys in-case this help anyone else out. I ended up running dual washers, standard 26 washers plus the ARP washers. Standard OEM 26 head gasket, and went another 15 ft/lb over on the torque. So far it's done 2 track days and a few runs here and there, no signs of pushing coolant and comp/leak down test done the other day was all good. Holding about 26psi fine.

Big thanks to all those that commented, and especially those that hinted about the dual washers.

Cheers.

  • Like 1
James_03 Mentor

James_03

Posted
  • Author
Posted

How come u didnt use a multi layer steel gasket mate?

I was concerned that the block face may have been out slightly, as I wasn't sure the washers would be the fix at the time, hence I decided to go composite thinking I would have better success that way if the block was out . That and other people have reported pretty good success with them after only doing ARP studs on standard NEO's and the like, similar boost to what I am running.

I suppose time will tell if that was a bad decision, I did work it hard at both track days but with only about 5 mins rest time at each event.

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      What brakes on R34 GTT(Europe)

      By GTSBoy · Posted

      I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Duncan
      What brakes on R34 GTT(Europe)

      By Duncan · Posted

      Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
    • 04-LOOX
      R34 GTR Vspec Garage Sale - All must go!

      By 04-LOOX · Posted

      Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
×
×
  • Create New...