Jump to content
SAU Community

Wheels/tyre Noise

INSANITI
 Share

Recommended Posts

INSANITI Collaborator

INSANITI

Posted
Posted

Hi All,

i have a 19incher wheels and running kumho Le sport KU39 245/35/19, i find that every 5k kms i have to realign my tyres as around 5000 kms it start to make that out of alignment noise.

Is this common?

should i increase my profile to 40series next time to lessen the frequency of alignment?

thanks

JT

Link to comment
https://www.sau.com.au/forums/topic/457982-wheelstyre-noise/
Share on other sites
Hadouken Grand Master

Hadouken

Posted
Posted

I had no idea you could hear when your tyres were out of alignment.

And sure. Run some 40 series tyres. Because, you know, that would be way closer to rolling diameter of stock wheels. Even the current profile is good and I bet your speedo isn't off or anything.

INSANITI Collaborator

INSANITI

Posted
  • Author
Posted

I'd say you're hearing the noise because it's pretty average rubber you have there. Once I got rid of my Kumho KU31s and replaced them with Michelin Pilot Sport 3 tyres, no more screeching around bends.

ok something to think about next time around..i though the le sports were pretty high end of the kumhos..

The Max Mentor

The Max

Posted
Posted

ok something to think about next time around..i though the le sports were pretty high end of the kumhos..

In my experience and very humble electrical engineer's opinion (i.e. I have no expertise in the field of tyres), Kumho don't produce anything high end when it comes to road tyres.

sonicii Veteran

sonicii

Posted
Posted

The KU36s I had were one of the best tyres I have used for grip and feedback, pitty they are insanely noisy. Not suitable for a daily IMHO, unless you have a car with a lot of sound insulation.

I have had KU19s too, and they were quite poor all round.

INSANITI Collaborator

INSANITI

Posted
  • Author
Posted

Hi Ben,

can you be a bit more specific? do you think its my driving style or the amount of times i hit pott holes? lolz

or could my cheap rims could be causing this? i have kings malice

If the alignment is changing that's the cars fault, not the tyres.

INSANITI Collaborator

INSANITI

Posted
  • Author
Posted

In my experience and very humble electrical engineer's opinion (i.e. I have no expertise in the field of tyres), Kumho don't produce anything high end when it comes to road tyres.

ok apart from michelins and pirelli's do you have other experience with other brands that are a little cheaper than them two? hehe

niZmO_Man Grand Master

niZmO_Man

Posted
Posted

The KU36s I had were one of the best tyres I have used for grip and feedback, pitty they are insanely noisy. Not suitable for a daily IMHO, unless you have a car with a lot of sound insulation.

I have had KU19s too, and they were quite poor all round.

He has KU39 not KU36. Kumho aren't the 'best', they are a good low-mid-range tyre. They aren't that quite either. My Subaru came with KU22 and they were quite noisy, changed to Momo M3, quieter and grippier, but can go more quiet (will next round of tyres, gonna get Michelin).

OP, you may have some worn bushes?

INSANITI Collaborator

INSANITI

Posted
  • Author
Posted

He has KU39 not KU36. Kumho aren't the 'best', they are a good low-mid-range tyre. They aren't that quite either. My Subaru came with KU22 and they were quite noisy, changed to Momo M3, quieter and grippier, but can go more quiet (will next round of tyres, gonna get Michelin).

OP, you may have some worn bushes?

Ok bought the car with 35k kms. i've done 75k now. tyres and wheels have done 16k kms. so you think time to go take it to pedders?

sonicii Veteran

sonicii

Posted
Posted

:) I wouldn't take box trailer to pedders.. But maybe some franchises are better than others..

I have had many good experiences with the local fulcrum suspension outlet, but I am not sure if they are in all locations.

As for the KU36, I know the op had 39s, I was just pointing out they do make a good tyre, if you can ignore the noise. A friend at work uses them on his turbo rx3 track car.. Where noise isn't exactly a problem.

But their 'mid range' tyres are quite ordinary.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      M35 Aftermarket Fuel Pump

      By MBS206 · Posted

      Pressure when IDLING, is meant to be 51PSi... So that amperage value needs to go up a fair chunk... I'd personally be factoring for more like 12amp at least on those runs, and at that point you need to hope the already there wiring doesn't drop you a volt or two, as that's a lot of fuel pressure flow drop off from 13.5 to 12V! Taking idle pressure of 51psi, means the pump will be drawing a MINIMUM of 9amps all the time based on your reading of the graph (3bar base, then allowing an extra 0.5bar for boost = roughly 51psi)
    • Ben_D
      Wanted to buy R200 longnose LSD 3.9 ratio

      By Ben_D · Posted

      Hi all,  I am in the market for an R200 longnose diff out of a Z31 300ZX, or S12 RSX, DR30 skyline, or similar, in a 3.9 ratio.  Preferably a late model one with the M12 crownwheel bolts.  The only easy to find advert for one of these was my ad back in 2007 when I sold it on this forum.  I sold the diff as I had sold the car it goes to, but as it turns out, after 18 years I got the car back late last year, so now I'm looking for the diff !  If anyone knows where to find a longnose R200 LSD with the M12 crownwheel bolts, drop me a line at [email protected] - Bonus paid if soomeone comes up with the original diff (stranger things have happened !).  Cheers   Ben D    
    • Ben_D
      Back for more after 18 years - and where are the longnose R200 LSDs?

      By Ben_D · Posted

      Hi everyone, I used to post here a bit from 2004-2013, when I owned various Nissans, in particular my S12 RSX gazelle, which was sold in 2007.  As luck would have it, after an 18 year hiatus, the car found its way back to me last year, and over the past 11 months I have had the pleasure of restoring it with my kids.  One thing that I am after in particular is a 3.9 ratio R200 LSD for it.  I actually sold the one out of the car here back in 2007 , and it would be incredible if I could track down who I sold it to, so I can see how they have progressed over the years (and to be honest, to see whether I can get the diff back !).  Anyways, hi all and let me know "where are the R200 Longnose diffs all at these days ?  Cheers Ben D  
    • sonicii
      G35 Control arm and Compression Rods into a V35 Skyline.

      By sonicii · Posted

      Arms will be the same as the G35 or 350Z, but as above, there was a change in the lower control arm where it connects to the ball joint.  That said, you can remove the ball joint cone from your old ball joints and fit them to the new ball joints.  To be honest, I didn't think the ball joints themselves were different. The main ball joint is a bit awkward to replace, you really need to remove the steering knuckle to press out the old one.  Some people have used tools to remove it in place, but it just seemed too hard to get to. If you are going to press out/in that ball joint, then you may as well just replace the bushings in the LCA and the compression rod.  You can buy the compression rod bushing from Nissan, but the LCA bushes, you will need to go aftermarket. Much cheaper than buying the whole arm.
    • Erelyes
      Ceramic turbine damage to engine - what did yours do?

      By Erelyes · Posted

      Ha, well, it's been.... a bit of a journey. Things have taken much longer than I'd hoped. I'll probably put up a thread at some stage. Hopefully soon. The car's not done any kms since my update in June though, put it that way.
×
×
  • Create New...