Jump to content
SAU Community

Recommended Posts

When replacing the headbolts I with arp items am I able to replace 1 bolt at a time as not to disturb head gasket or will I have to replace the headgasket? I'm also replacing vale stem seals and valve springs so would I be better to just remove the head?

Not sure on your specific engine (as I have never seen that engine in person), but I did this exact job on a 2JZ Supra. It's not easy working valve stem seals all day laying on the engine, and depending on miles you may want to take the valves out and lap them / clean / port the head while you are at it for not much more expense than a new head gasket...which isn't a lot of money. But if you are talking valve stem seals, then I can assume it's got some miles. I would be pulling the head unless you just want it to stop smoking on startup and off idle.

Also I'm sure the studs could be changed while the engine is in the car, but you may want someone to cofirm.

My .02.

Edited by HarrisRacing

Engine has 100,000 km on it. Didn't really have any problems just thought I should do them while in there. I was going to get a valve/ port job but it was quickly dismissed as a waste of $$ at my goals ~350rwkw on 98

But if I disturb the headgasket is there I chance I will need to reface the head or block?

If using a metal gasket the block should ideally be machined correctly for it. It's good practice to machine the head when removing it also but I wouldn't say it's mandatory.

Give it a go with the head on. It's been done before. Royce did it and is making stupid power, like over 500rwkw or something.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
    • For DBA, check out their guide table here. https://dba.com.au/wp-content/uploads/2023/01/Direct_Replacement-Guide-2021.2.pdf   Additionally they have some other guides and info on how to make sure you choose the right pad.
×
×
  • Create New...