Jump to content
SAU Community

Recommended Posts

Hey mate,

I have 19s on mine. They are 245/35/19. They fit fine and are apparently legal size on a 33. I was recommended against 265s since they might be that little bit too wide. The bloke i spoke to about it was not 100%, so they might fit.

Good luck! Let us know how they go...

Hey mate,

I have 19s on mine. They are 245/35/19. They fit fine and are apparently legal size on a 33.  I was recommended against 265s since they might be that little bit too wide. The bloke i spoke to about it was not 100%, so they might fit.

Good luck! Let us know how they go...

Thanks for your help. I don't think it will be the actual rim size but the width might matter since your's are 245's.. what about 265?

oh i have standard shocks so not sure but if anyone else can helpp would be great!

thanks

Thanks for your help. I don't think it will be the actual rim size but the width might matter since your's are 245's.. what about 265?  

oh i have standard shocks so not sure but if anyone else can helpp would be great!

thanks

They are tyre sizes you quoted not wheel sizes they will fit or not fit depending on the offset of your wheels

235 40 18 front 265 35 18 rear fit fine on mine but 255 35 17 on different wheels fouled the rear suspension.....depends entirely on your wheel offset

I am going to be purchasing some wheel and the size are:

Front : 235 35 18

Rear : 265 35 18

Can these wheels fit R33 GTST without rolling the guards?

I've got 18x8s (offset +38) all round with 235/40/18 on the front and 255/35/18 on the rear and everything is a perfect fit. I'm actually a little annoyed that I didnt go the 265s.

i've got 17x10 inch rims at the back and they definitely fit. 17 x 9 inch at the front, also fit no probs. The rear just misses the caliper and also misses the guards. My guards have not been rolled.

As said above, 2xx is the tyre width, not the wheel width. I am currently running stretched 255 rubber at the back. Nice and firm tyre wall

thanks for all the reply and help guys. much appreciated. sorry for my noobness when it

comes to rims. had a look at this site:

http://www.driverstechnology.co.uk/Tyre_si...size_coding.htm

and was wondering wouldn't 265 rear on R33 GTST will scrape the guards? 35 is the profile if i am correct? ;):rofl:

it all depends on offset. You have to find a balance between scraping the brake caliper and the guard. Get one that fits properly, and 265 should fit easily. Like i said, i've got 10 " wheels. If i was not using stretched rubber, who knows what the recommended rubber is, 285? easily fits

legal once/if you get them engineered :D

Depends on the state the car is registered in though... Some allow you two wheel sizes, others only care about offset (and increase/decreasing the track width), etc. Check with your licensing authority.

LW.

thanks for the continual help guys. so I guess the wheels im gettng Front : 235 35 18

Rear : 265 35 18 will fit on a R33 GTST :D

thanks!

We don't seem to be connecting with you??? You STILL have not quoted the offsets on the wheels you'r getting....so....on the info you have actually given us your wheels MAY or MAY NOT fit!!! it depends entirely on what the offsets of those particular wheels are. :headspin:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Could be. Could also be that they sit around broken more. To be fair, you almost never see one driving around. I see more R chassis GTRs than the Renault ones.
    • Yeah. Nah. This is why I said My bold for my double emphasis. We're not talking about cars tuned to the edge of det here. We're talking about normal cars. Flame propagation speed and the amount of energy required to ignite the fuel are not significant factors when running at 1500-4000 rpm, and medium to light loads, like nearly every car on the road (except twin cab utes which are driven at 6k and 100% load all the time). There is no shortage of ignition energy available in any petrol engine. If there was, we'd all be in deep shit. The calorific value, on a volume basis, is significantly different, between 98 and 91, and that turns up immediately in consumption numbers. You can see the signal easily if you control for the other variables well enough, and/or collect enough stats. As to not seeing any benefit - we had a couple of EF and EL Falcons in the company fleet back in the late 90s and early 2000s. The EEC IV ECU in those things was particularly good at adding in timing as soon as knock headroom improved, which typically came from putting in some 95 or 98. The responsiveness and power improved noticeably, and the fuel consumption dropped considerably, just from going to 95. Less delta from there to 98 - almost not noticeable, compared to the big differences seen between 91 and 95. Way back in the day, when supermarkets first started selling fuel from their own stations, I did thousands of km in FNQ in a small Toyota. I can't remember if it was a Starlet or an early Yaris. Anyway - the supermarket servos were bringing in cheap fuel from Indonesia, and the other servos were still using locally refined gear. The fuel consumption was typically at least 5%, often as much as 8% worse on the Indo shit, presumably because they had a lot more oxygenated component in the brew, and were probably barely meeting the octane spec. Around the same time or maybe a bit later (like 25 years ago), I could tell the difference between Shell 98 and BP 98, and typically preferred to only use Shell then because the Skyline ran so much better on it. Years later I found the realtionship between them had swapped, as a consequence of yet more refinery closures. So I've only used BP 98 since. Although, I must say that I could not fault the odd tank of United 98 that I've run. It's probably the same stuff. It is also very important to remember that these findings are often dependent on region. With most of the refineries in Oz now dead, there's less variability in local stuff, and he majority of our fuels are not even refined here any more anyway. It probably depends more on which SE Asian refinery is currently cheapest to operate.
    • You don't have an R34 service manual for the body do you? Have found plenty for the engine and drivetrain but nothing else
    • If they can dyno them, get them dyno'd, make sure they're not leaking, and if they look okay on the dyno and are performing relatively well, put them in the car.   If they're leaking oil etc, and you feel so inclined, open them up yourself and see what you can do to fix it. The main thing you're trying to do is replace the parts that perish, like seals. You're not attempting to change the valving. You might even be able to find somewhere that has the Tein parts/rebuild kit if you dig hard.
    • Can you also make sure the invoices on the box (And none exist in the boxes) are below our import duty limits... I jest, there's nothing I need to actually purchase and order in. (Unless you can find me a rear diff carrier, brand new, for stupidly cheap, that is for a Toyota Landcruiser, HZJ105R GXL, 2000 year model...)  
×
×
  • Create New...