Jump to content
SAU Community

Recommended Posts

Ola Peops,

Just curious to see, if i could tempt anyone to part ways with their R34 Gtr? (Prior to going down the ICI route).

* Prefer white, then black.

* Basic mods, not looking for anything highly modified

* Budget around 50k give or take, depending on vehicle and condition

* All supporting paperwork a must (de-reg etc)

Lastly located in Nsw but will travel between Old and Vic

Pm here first.

Edited by Hazamat
Link to comment
https://www.sau.com.au/forums/topic/458954-wtb-r34-gtr/
Share on other sites

  • 3 weeks later...

Bump, moving budget to $58,000 (dependent on car)

Hi mate - I'm considering letting go of my baby. It's been with me for 6 years and is my weekend ride.

R34 GTR Vspec bayside blue, gunmetal grey stock rims. Everything on this car is clean and stock. Oil (Motul 300V) change every 6 months and full service every year. This car is clean inside and out. I'm looking at $60,000 but willing to negotiate.

Located in Melbourne.

Thanks,

Michael

Edited by mdang
Link to comment
https://www.sau.com.au/forums/topic/458954-wtb-r34-gtr/#findComment-7597227
Share on other sites

Hi mate - I'm considering letting go of my baby. It's been with me for 6 years and is my weekend ride.

R34 GTR Vspec bayside blue, gunmetal grey stock rims. Everything on this car is clean and stock. Oil (Motul 300V) change every 6 months and full service every year. This car is clean inside and out. I'm looking at $60,000 but willing to negotiate.

Located in Melbourne.

Thanks,

Michael

How many kms has it done mate? Genuine?

Link to comment
https://www.sau.com.au/forums/topic/458954-wtb-r34-gtr/#findComment-7597292
Share on other sites

  • 1 month later...
  • 2 weeks later...

Hey I'm thinking about selling my car done about 7k since full engine rebuild with a Brian crower 2.9l stroker kit and new n1 block. looks dead stock under the bonnet making 441kwatw on 24psi.

It's white on black work Meisters s13p.

Send me a message if you want further details. post-139028-14467139116458_thumb.jpg

Edited by brockm89
Link to comment
https://www.sau.com.au/forums/topic/458954-wtb-r34-gtr/#findComment-7632611
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
    • Does it also misfire equally when revving?   Josh is very correct in what you should do. The coilpack harness wiring loom itself is a known problem due to its age and the number of heat cycles it has gone through. Throwing parts at a vehicle to diagnose the issue isn't a smart or good way to do it. Secondly, you may have a bad coil pack, you pop replacements in, they fix that issue, but messing with the harness breaks it, so the issue persists. So now you think "well it wasn't the coil packs" and have to continue chasing your tail, potentially swapping back in your shit coil packs and returning the good ones (yes, I've seen people do this because 'it wasn't the problem' and they want to save money). And suddenly, you've got two issues with the same symptoms...   Diagnose, don't use the spare parts shotgun.
×
×
  • Create New...