Jump to content
SAU Community

Recommended Posts

Im not discrediting their work, i am letting you know from my experience (take it or leave it). Im all for supporting local business but just giving you the heads up these vq low rev engine sounds are bloody loud (especially in the cabin) where you will be on a constant dose of panadol for the headaches.

I have spoken to one of the local m35 owners here in brisbane about his experience and he mentioned he changed to a diesel muffler and had it sticking out a little more from the rear of the car so the exiting noise was past the rear of the car not under it. Happy trails with you're shop just food for thought.

You're comment sounded like me a few years ago. Now i have a exhaust that was made for the nm35s.

I always appreciate the information and opinions.

I ran an N1 exhaust first on my M35 but went fully custom due to the drone and have had custom for the last year and a half. Compared to what i have heard on youtube clips etc i would hardly call mine droney or loud in comparison but then again my experience with M35's is fairly limited to 3 owners cars.

I may regret not going for a Fujitsubo this time but i'll try and post a clip once mine is sorted for science.

Diesel mufflers are pretty much larger cylinders with a perforated hole pipe that's straight through. Some glass packed or not. Most of the mufflers off the shelf have baffles or loops inside (don't get me started on bullets and cobys). Effectively just makes it like the branded ones without the label price. Cut one open

Edited by Reaperblitz

"if made badly or ignorantly"

I am getting a new exhaust made in the next few weeks. I'll try and post up how it sounds when done. I guess i could have just gotten a new dump / flex and joined the Fujitsubo crew but i like tackling things my own way with what i have at my disposal locally. Support the locals folks :)

If the bloke i am using's other work is an indication of what i'm in store for it should be a nice bit of kit.

You'll have much less of an issue with the drone situation with the manual conversion; which is yet another good thing to add to the enormous list of good things about manual cars... :cheers:

  • Like 2

I have Bricks intake now.

Haven't fitted yet, gees imagine would probably be over 120db.

Video coming soon of my Fuji with single cell cat.

My work associate said he could hear me for a good minute before I pulled up to site.

I like the look of that silencer, looks smart.

If the new cat doesn't bring it down enough I might try one of those.

That doesn't sound like any Fujitsubo I have heard under load.

Does it look like it has been tampered with? Resonator still intact? Maybe the rear muffler has been gutted of the baffling by the previous owner?

  • Like 1

That doesn't sound like any Fujitsubo I have heard under load.

Does it look like it has been tampered with? Resonator still intact? Maybe the rear muffler has been gutted of the baffling by the previous owner?

I was going to say; mine sounds nothing like that.

That has a rasp that is completely absent from mine.

Is there a cat fitted?

With a sound meter phone app (no guarantee of accuracy) mine only registered 90dB at peak (free rev).

But even allowing for error; there's no way known that it would be 107dB, I have mates with bikes around 104dB, and they are orders of magnitude louder than my quiet ol' Fuji.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...