Jump to content
SAU Community

Recommended Posts

Hi all,

Just wondering how many of you out there has ever had an engine go on you, you know, big stuff like cracked pistons, ring lands, rod failures, valve gear problems, head gaskets, etc etc.

If you can state generally what level of tune you had (rwkW) and why you think it happened, it would interesting to know.

Looking forward to the horror stories!

Freebaggin.

Link to comment
https://www.sau.com.au/forums/topic/4625-whos-blown-their-rb-engine-and-why/
Share on other sites

At the 4 6 & rotary nationals in Feb this year, I blew up

my RB26 engine in the R33 GTR.It had around 340 rwkw using

bolt ons like HKS 2540s,FMIC,etc, but the engine itself was

untouched. I did 2 back to back runs, which was silly cause it was

too hot & the oil system must not have been able to keep up.

It ran 11.5 & 11.6 and on the second run developed a loud rattle.

When we pulled the engine down, the no. 4 conrod bearing was

completely missing except for a wafer thin bit left welded to the

crank!It was amazing the whole lot didn't let go through the traps.Also the crank was bent 2 thou & one of the pistons had been bouncing off the head.Keir wilson(R32 GTR 10.5fame) bought

this engine, rebuilt it and ran 10.6 at drag combat with it!!

So, providing they dont throw the rods out of the block, they can

be rebuilt quite easily.On the same day in Feb, Keir was not so lucky with his R32.Oil starvation through the traps welded the crank to the block & KABLOOEEE.

I remember grabing Brenton's Adelaide Clutch ute & hooking down to help him.One of the safety guys came over & passed me a handful of bits off the track.One of the bits was a bit of the block

with san (part of the nissan) on it! What a mess.Other than the Head the whole thing was scrap metal.

Now we both have OS 3 litre engines with larger,baffled sumps.

Hope it dosen't happen again, but when you rev over 9000 rpm

nothing lasts forever.

:flamed:

Originally posted by adam 32

blew up my internally std RB20

too much boost from the T04 and not enough fuel!!

made around the 280rwhp mark i think before it blew

hehehe I told you dont tinkering with boost! :P:cool:

hehehehe... how is your car running now? all fixed I hope:)

cheers

Joe

Guest nismogtsx

I did a couple of valves in cyl no. 2 when the conrod snaped and left the piston at the top... LOL The next rotation the valves opened and they hit the fused piston.... The mechanic who rebuilt had to drill the piston out of the cylinder it was that well fused....

My main point is that with mods the cars run well, but i was doing 230rwkw all the time and the conrods were standard... Now their a Nismo part... Got them fairly cheap....

Guest nismogtsx

I totally forgot my point.

Anyway i did all the bottom end but didnt wait for the rods to come. I got too hasty and re built my motor with the original 100,000km conrods and they lasted 3 months... So thats not bad... But you need to have a weak point in every motor.... Because there's no such thing as bullet proof.....

NOTE: Build it stong and give it heaps when you wear it in so the parts bed in hard and are ready for a hard life....

  • 1 month later...

Engine 1: 145 RWKW T3/4 High Flow Trust FMIC..... Standard Fuel Pump....ang bang rattle rattle.... too lean....

Engine 2: Sheared the cam belt tensioner bolt and lunched the head.... I've been told someone may have replaced the cam belt idler bearing and overtightened the bolt??

Engine 3: Still running hard with 180 RWKW... new owner hasn't blown it (yet)

BIG chunk of #1 piston - down to the ring land - parted company with the rest of the piston, and played pinball inside the combustion chamber. Also broke the top ring and bent an end of it upwards. Amazingly, not outwards, because bore is totally unmarked.

I suspect a dyno run had it lean out and detonate at the top end (fuel pump incapacity), but no proof.

Had a mild build - T3/T4 hybrid, FMIC, only about 115 awkW.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...