Jump to content
SAU Community

Bee*r Limiter For Rb25 + Pfc Help.

Jaydn_033
 Share

Recommended Posts

Jaydn_033 Newbie

Jaydn_033

Posted
Posted (edited)

Hi,

before I get flamed about this I am very aware of the potential damage a Bee*R limiter can cause to components

of my engine, however it is not a standard rb25 and am more than happy to fit one as I don't have a PFC pro.

I bought a second hand Bee*R limiter recently and have just installed it but it will not work correctly,

I've looked up countless posts about fitting them and I just can't see what I've done wrong at all.

I have only "spliced" into two wires of the ECU loom and are using separate 12v + grounds as the

PFC has a grounding issue with the Bee*R.

The wires are set up as follows:

YELLOW - spliced into pin 41 on ECU (crank 120)

GREEN - spliced into pin 42 of ECU (crank 1)

RED - spliced into 12v on radio

BLACK - spliced into ground of cig lighter

WHITE - spliced into handbrake wire

BROWN LOOP - did not cut

GREY LOOP - did not cut

The issue I am getting is that the Bee*R will turn on (red LED stays lit solid while car is on) but no matter what setting, handbrake up or

down, it will not hit the limiter. It's as if the Bee*R was not there at all but it is obviously receiving power as it is lighting the LED up on the unit.

Tried swtitching the yellow and green wires around with no luck, the car would start and run as normal but the Bee*R unit would not light

the LED up.

I have no idea what the next step might be, I've taken the unit apart (I don't know too much about electrical boards) and cant see any obvious

signs of damage to the board at all so I'm a bit confused, the only other thing i can possibly think of is the actual Bee*R unit itself isn't working

properly and is damaged?

Any help would be greatly appreciated.

Thanks.

Edited by Jaydn_033
Link to comment
https://www.sau.com.au/forums/topic/462579-beer-limiter-for-rb25-pfc-help/
Share on other sites
Dose Pipe Sutututu Grand Master

Dose Pipe Sutututu

Posted
Posted

My suggestion is to get a proper ECU with adjustable retard and adjustable RPM ignition and / or fuel cut for your bang bang.

I have what you're trying to achieve governed by my vehicle speed so no silly handbrake needed.

  • Like 1
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      NC MX5

      By Dose Pipe Sutututu · Posted

      The German place in Cabramatta was rock solid, fresh pretzel cooked to order back then. Then it went all quiet, after all the poker machines were removed, then I believe it closed for good. I did drive past the other week and noticed outdoor lighting a big screen, but no idea what is there now.  
    • joshuaho96
      R33 GTR running -9 with no tune

      By joshuaho96 · Posted

      Yeah I suspect even if you hold airmass per cycle/cylinder constant if you get too far away from stock you're still going to have problems running the factory tune within the bounds of the factory load scale. Cams, different displacement/rod ratio, etc. I'm just lucky that the GTIII-SS with wastegate boost + CA compliance cats is pretty much equivalent to stock turbos. When I have actual space I can finally get it tuned and modify the fuel system for flex fuel to 100% handle any detonation concerns when cranking the boost to whatever those dinky turbos can put out.
    • The Bogan
      NC MX5

      By The Bogan · Posted

      I would say no, why, because my daughter, who also lives in Goulburn, hasn't recommended us going there Pity, as we miss all the German joints around in Sydney, actually, the restaurants are the only thing I really miss about Sydney, and a special mention to Ishibanboshi at Bondi Junction, their Kara-age Don is heart cloggingly deliciousness (always added a special boiled egg...or 2) 😋 
    • GTSBoy
      NC MX5

      By GTSBoy · Posted

      Does that German restaurant still exist in the old place out the NW end of Goulburn? When I say "out the NW end of"...I am really being vague. It was 1997 when I was last there, and the only point of reference I can recall is that it was on the opposite side of the main drag from the big merino. And when I say "opposite side of the main drag", I don't mean "on the main drag". It was either a couple of streets back from there, or might have even been out in the sticks a bit further. Was an old farm building or mill or somesuch. And when I say "the big merino" I might actually be thinking of a completely different part of town, because I just looked on maps and the big bugger is not where I remembered him to be! The food was good, consisting largely of various German mystery-meat sausage/loaf things and kartofflen.
    • GTSBoy
      R33 GTR running -9 with no tune

      By GTSBoy · Posted

      So while the second sentence is completely correct and the whole point of the conversation, the first sentence bears consideration. If this bloke is just hoping to throw big turbos on and drive it around, because there are no helpful facilities at all in his tropical paradise** then he likely has zero chance of even knowing what the TP is on the last column in the stock maps, let alone know whether the ECU is operating anywhere near it or past it. So the point is very very moot. And, per what I said before, at stock boost on those turbos, you may well be off the end of the map. **I'm just back from Vanuatu, so I know exactly what small Pacific nations can be like wrt paradise without requisite facilities. But it's not even that simple. I put a high flow on my car and had to drive it around without a proper tune because of the lack of opportunity*** to put the bigger AFM and injectors into it to allow it to be tuned. I had to turn the boost down to less than I had before, and back off the boost controller's ramp, because it was exploring parts of the map that it didn't drive in before, and really couldn't access for tuning on the dyno either, and so was pinging. It was still well within the last column, because when I first**** set up the Nistune on the Neo I rescaled all axes of the maps to give some more space to explore. ***Family dyno was broken ****This was 13 years ago, and the TIM thing wasn't a thing then and so TP would definitely grow when pushing past the stock tune's limits.
×
×
  • Create New...