Jump to content
SAU Community

Which Oil To Use On Clutch

alexboland

By alexboland,
in General Maintenance

 Share

Recommended Posts

MrStabby Grand Master

MrStabby

Posted
Posted

Get some squeaky clutch oil from superheap.

It is applied in the bellhousing straight onto the clutch plate/s

Stop being cruel.

OP - do you know where the squeak is from? Is it the pedal?

  • Like 1
kingtube69 Experienced

kingtube69

Posted
Posted

Typically squeaks from two places:

1) Clutch pedal assembly - Spray some dry lube (is there such a thing heuheuheu) - Available at bunnings, supercheap etc.

2) Clutch pivot - Need to look up how to do this. I've heard of people doing this with the box on the car and off.

XGTRX Veteran

XGTRX

Posted
Posted (edited)

2) Clutch pivot - Need to look up how to do this. I've heard of people doing this with the box on the car and off.

Done it by removing the slave and pulling back the fork, very long nose pliers with folded paper with purple grease on the end, cable tie your pliers shut and slip the paper between the fork and pivot. Pain in the arse though but can be done. Edited by XGTRX
  • Like 1
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R32 GTS (RB20DE) Injectors Replacement

      By GTSBoy · Posted

      Stock RB fuel pressure is near enough 43.5 psi, so the latency in that table at 31.6 will be close. You can see that 7 or 8 psi equates to about 0.4µs extra latency. So if you wanted to interpolate between the 31.6 and 39.9 psi values you could say you're going up about 2 psi out of those 8, so add about 0.1µs, which is barely worth talking about and is quite possibly wrong because ideally you would fix the latency while running at the appropriate conditions on the dyno, with a wideband sniffing its butt.
    • MBS206
      R32 GTS (RB20DE) Injectors Replacement

      By MBS206 · Posted

      The pressure, is what you set the fuel pressure to. If you have the factory fuel reg, you'll need to find the factory spec. I don't know it off the top of my head, but someone else might.
    • MBS206
      Belt flex under throttle

      By MBS206 · Posted

      For others, what GTSBoy states here should be paid attention. Why? Well lots of people play with different engines, and they LOVE to change things like remove AC, or steering pumps etc, and it lends to them needing to move the tensioner too. You want your tensioner, particularly those that are sprung or hydraulically tensioned, to be the first thing after the harmonic balancer, or technically the "last" pulley in the chain. By saying last pulley, I mean look at the direction the crank spins when the engine is running, follow the belt from where the crank is pulling the belt FROM, and keep following that until you're between the last pulley/accessory on the belt and about to reach the crank again, this is the spot where you put the tensioner. This is the area that will always end up with slack. This is worked out exactly the same way for chains too, as the physics is the same for them. The crank pulley is where all the force to drag the belt around comes from. You will never ever get rid of the slack that appears, especially under load. The tensioners job is to keep the belt loose enough when stationary that there shouldn't be out of sync movement in slow movement, and then be tight enough when running, that the belt can't jump off any gear and get damaged. Too tight, bad things happen, too loose, bad things happen. Have a tensioner (mainly sprung/hydraulic one) in the wrong spot, it can't actually do anything about keeping the tension.
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      It was gonna take much longer for the 440cc so I'd thought I'd risk it with the 550cc. They finally arrived and I couldn't wait any longer (I could but I was quite excited after 2 months) and installed them myself. Removed the old injectors, inserted the new and connected everything up. Before starting the car, I tuned the injector size from the factory 270cc to 550cc using Nistune.   This did some of the calculations automatically which catered for the TIM. The latency however did not seem to change. Deatschwerks have the tuning data available for each injector online, and I had a look at it. It has a table which relates to latency according to pressure and voltage (see below image). Nistune requires the 14v value, but I am unsure of which pressure value to look at (my lack of knowledge and experience have something to do with this). The highlighted value is close to my current latency which is 760µs. It is for 14v which makes sense, and the pressure is 31.6 Psi.   I still gave the car a test drive to see how it goes, and honestly it has never felt so powerful before (and some people say the RB20DE is very weak?). I really enjoyed the drive. Side note; The injectors are quite noisy, which someone mentioned before. This does not really bother me however. I will still ask my mechanic to have a look at it and perhaps ask a tuner to fine tune it if they have the knowledge.
    • GTSBoy
      RB26 swapped gtst

      By GTSBoy · Posted

      Also true. But imagine not wanting new injectors? Imagine wanting to use 30 year old injectors?
×
×
  • Create New...