Jump to content
SAU Community

Recommended Posts

Hi everyone,im new here and a helpfull assist would be much appreciated..

I have a BNR34Vspec 2001 and facing a problem tat after my car came to a fullstop,after a few seconds my 4wd and A-LSD lights got turn on..after restarting it again everything went normal and it got turn on again after a few second of fullstop..ive checked the resovoir behind the rear boot and fluid are at the max level..ive been tru and read forums but couldnt find a problem that happenned exactly like mine..

I wish to try solving it myself so is there any idea where i can start from?

Help and assist are most appreciated and pls to meet everyone here since im new here and also new to my car

Cheers everyone!!

Link to comment
https://www.sau.com.au/forums/topic/463322-4wd-and-a-lsd-lights-onbnr34vspec/
Share on other sites

I did tried finding the spot to read ecu code behind the boot and ended up clueless where its is..tru reading from forums reading ecu codes from boot isnt it apply only for r32 and r33?

Thanks for the reply Hadouken :)

Meathead:u mean after the lights turn on,shut off the and turn on the engine and give it a 1000rpm and see if the lights are on again?ok ill gv it a try by tis evening..if lights still turn on after wat u intruct me to do means theres a TPS failure right?do correct me if im wrong

Thanks for the reply ill update after ive try it out.cheers

Meathead:u mean after the lights turn on,shut off the and turn on the engine and give it a 1000rpm and see if the lights are on again?ok ill gv it a try by tis evening..if lights still turn on after wat u intruct me to do means theres a TPS failure right?do correct me if im wrong

Thanks for the reply ill update after ive try it out.cheers

Yeah with the engine switched off start it and keep the rpm 1000 and above for a few minutes and see if the Alsd light is on, if it is not and you let it come back to idle does the Alsd light illuminate after a while again ?

You may have a fluctuating idle that goes below normal and sends a low TPS signal to the Atessa cu which will cause the alarm

TPS signal to Atessa on my r33 gtr vspec is 0.3 - 3.7 v if it falls outside of this it will fault.

You could check the AAC valve (under plenum - 4 bolts and a plug) give it a clean and renew the joint. Idle can be adjusted with the screw.

Lots of AAC cleaning threads here in SAU to help you.

If you are not sure get someone else to do it, preferably a friend as a shop will probably sting!

I am not saying this is your problem but it could be. Might be dirty plugs also causing hunting.

Good Luck!

Edited by Meathead
How tf is hunting and dirty plugs related to a 4wd light?[/quote

Hey tf your mouth runs before your brain

You should question other posters in a more civil way.

Tps is directly proportional to rpm which signal inputs to atessa tf

If you could not figure that out then maybe you should just pull your head in tf

Meathead:ive tried as u intructed..like revving above 1000rpm..the lights did not turn on..but as i let go the acceleration my rpm idle show slightly above 1000rpm,is tat a normal?

BTW,wat AAC valve means..?sorry for a noob question..trying to learn as much as i can

Thanks for the reply and point outs..

Not the obvious culprits then.

You should seriously see what fault code is coming up, lots of things can trigger this. ie wheel speed sensors for one.

Regarding far fetched - not at all mate Atessa takes rpm signal also and if the rpm signal fluctuates below a certain range say from hunting caused by fouled plugs it will error. \

Count grantleyish:the 4wd and A-LSD comes on whenever the car come into fullstop...i didnt time lap how long it needs to be driven to alarm the lights to go on..as if itll turn on as long as car stop moving and after few seconds..it came on..

Meathead:yeah,mayb ill take your advise and do a scan just like GTSBoy suggested...but before goin into that i would like to gv a bleed to the attesa system fot any trap air..will update see if this gonna work..cheers everone and thanks

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi Guys, Does anyone know any aftermarket part numbers for a starter motor to suit the VQ25DET? I can find lots of alternative part number for the VQ35DE, which I assume would fit, but there is a lot of conflicting information out there. Thanks..
    • I don't understand how this hasn't boiled down to - Upgrade the turbo when you have everything required. ECU, injectors, fuel pump, turbo, etc. Do it all at once.  If you don't have everything required, just enjoy the car as it is and keep saving up your pennies. 
    • Sounds like you've got an interesting adventure ahead here with local support if you have trouble! My guess is that, unboosted, you will be OK with a small upgrade like -9. What will happen is that once the stock ECU sees more airflow than it expects it will add a heap of fuel and pull a heap of timing to be safe because it can't understand how it could get that much air without there being an issue. You will see clouds of black smoke and it won't pull hard through the midrange and top end. So, overall it will be a bit frustrating but should be OK. If you are still nervous set the base timing back 2o through the CAS, but it will be even more sluggish everywhere. As said above through...this is not my guarantee your engine won't be blown into a million pieces, leaving you looking for very hard to find parts A better idea is get a computer with logging ASAP, wire in a wide band O2 sensor and a use remote tuner. I've done multiple cars this way and while it is not as good as a specific tune on a dyno they can get it 90% right. I'd suggest if you can afford an R33 GTR these days you can afford an ECU and tune. And if you can't afford that you sure won't be able to afford the rebuild if it goes bad in the meantime,.  
    • Yeah it would be nice if someone took the time to put that sort of information together, but there are a lot of variations in looms. I think you are making this way hard for yourself if you just want to get it running....sourcing an SR20 with the right wiring will be a billion times easier than matching the RB loom to an S15 chassis. If you do end up going this way, you just need to trace every wire in the loom with a multimeter, 95% of them will go to a location you can confirm at the ECU.....and then post it up for the next person who needs it  
    • Just top it up with water, and keep a general idea of how much you added. It is normal for water to be pushed into and pulled out of the reservoir through the cap, and it should not be more than half full or it will be likely to overflow when hot. Any decent mechanic can do a pressure test of the cooling system to confirm if you have a leak. Keep in mind if it is only leaking a little and when hot it may well evaporate before you see it hit the ground
×
×
  • Create New...