Jump to content
SAU Community

Recommended Posts

genuine xenon kit

HID_BOX-3.jpg

XENON HID provides more than twice the amount of light of a halogen bulb, it does not have a filament. Instead the light is created by an electrical discharge between two electrodes in an air tight tiny quartz capsule filled with xenon gas, mercury and metal halide salts. This improves durability as road vibrations can cause damage to coil lighting technologies. These light sources also produce a blue-white light that is safer because it is closer to natural daylight. The color temperature is approximately 5000-13000 K compared to 2300-3000 K for halogen. The increased light output from a 35 watt XENON HID lamp is approximately 200-300% more light output than a 55 watt halogen bulb. The XENON HID system will also draw less power from your vehicles electrical system.

we will donate 5% form each sale to SAU

prices : 5000k kit RRP $879 SAU Price $709

8000k kit RRP $899 SAU Price $749

(note :H4 Hi/Lo extra $25)

fitting sizesH1, H3, H4 Lo, H4 Hi/Lo, H7,9005, 9006

if you have any queries please contact

Martin

IBS Electronics

93a Liverpool RD

Summer hill NSW 2130

phone (02)9798-7919

fax (02)9797-9471

www.ibselectronics.com.au

[email protected]

Link to comment
https://www.sau.com.au/forums/topic/46390-donation-sale-hid-kits/
Share on other sites

  • 2 weeks later...

the globes igniter and ballast are made in germany

wiring hrness and pakaging in taiwan

8000k is uv when using florescent light scale

this is light scale for gas discharge

i use the 8000k in my car

anyone is more than welcome to inspect the quality of the product and light output

just send me an email and we can meet anywhere in sydney

or you can come to my store and ill show you how it works

  • 3 weeks later...

It might sound like a dumb thing to say but I thought that to go to HID you'd need to buy new lamp assembly's that have a higher heat tolerance due to the high heat output of the Xenon discharge lamp?

Just a thought... plz correct me if I'm wrong.

Dan

xenon is actually lower heat output... these kits are manafactured to replace the bulb type in your standard headlight assembly.

Simply remove your halogen bulb and install this kit and you have converted to HID...

Its been around for some time now.

I've got a set of xenons in my r33 gts-t and they're fine. Had them for a few months now and no problems with heat/melting etc.

These hids are not the same as what I have. I don't know about this particular brand.

  • 4 weeks later...
  • 2 weeks later...
  • 4 weeks later...
  • 2 weeks later...
Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...