Jump to content
SAU Community

Recommended Posts

I imported my R33 V-Spec from Japan in Dec last year, I am having a few engine tuning (missing, loss of power & extremely rich) issues which I am working thru

I have replaced the usual Plugs, AFM, coil packs (replaced with Okada projects for future tuning), injectors tested & cleaned, manifold gaskets replaced...

Turned the V-Cam system off & still the issue remains, next step is an aftermarket ECU

I pulled the ECU out & opened it & i cannot identify what this is?

it seems to have a "Daughter board" stuck on top of the main board (referred from R33 GTR ECU pics )

Questions,

1. Is this STD?

2. If not STD what make is it?

3. can it be tuned?

4. can it be removed so an aftermarket ECU can be fitted?

as I am new to this any help would be appreciated...

post-141727-0-53354400-1462536519_thumb.jpg

post-141727-0-01825100-1462536540_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/464654-help-what-ecu-is-this/
Share on other sites

# is 2371024U01 of the front of the ECU case

Then ECU # seems to be correct when referenced by Nissan, it is the "piggy back" daughter board that I think has scrambled

The battery was disconnected when shipped & then a few times after that, possibly could have lost or corrupted memory parameters

From my on-line searches it seems to be an "Techtom" board which is apparently tune-able but I am still trying to find how & what program...

Edited by AussieR33GTR

Yes I understand that it is a STD ECU

but when I google R33 GTR ECU this is a STD comp (pic DSC00547)

As mine has a 2nd board (pic 201718) stuck on top, that is what I am trying to find out details about

post-141727-0-58598200-1462587911_thumb.jpg

post-141727-0-72566900-1462587975_thumb.jpg

Edited by AussieR33GTR

Ben,

I contacted Matt @ Nistune & he confirmed that it is a TechTom board, thank you for the contact

There are not many people in Australia that can "tune" this board so basically the ECU gets shelved

I am purchasing an Emtron this week so at least there will be unlimited tuning capabilities

I must say that the response time of Matt from Nistune was fantastic...

Ben,

I contacted Matt @ Nistune & he confirmed that it is a TechTom board, thank you for the contact

There are not many people in Australia that can "tune" this board so basically the ECU gets shelved

I am purchasing an Emtron this week so at least there will be unlimited tuning capabilities

I must say that the response time of Matt from Nistune was fantastic...

Great you found an answer.

Matt is fantastic, super helpful.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
    • I forgot about my shiny new plates!
    • Well, apparently they do fit, however this wont be a problem if not because the car will be stationary while i do the suspension work. I was just going to use the 16's to roll the old girl around if I needed to. I just need to get the E90 back on the road first. Yes! I'm a believer! 🙌 So, I contacted them because the site kinda sucks and I was really confused about what I'd need. They put together a package for me and because I was spraying all the seat surfaces and not doing spot fixes I decided not to send them a headrest to colour match, I just used their colour on file (and it was spot on).  I got some heavy duty cleaner, 1L of colour, a small bottle of dye hardener and a small bottle of the dye top coat. I also got a spray gun as I needed a larger nozzle than the gun I had and it was only $40 extra. From memory the total was ~$450 ish. Its not cheap but the result is awesome. They did add repair bits and pieces to the quote originally and the cost came down significantly when I said I didn't need any repair products. I did it over a weekend. The only issues I had were my own; I forgot to mix the hardener into the dye two coats but I had enough dye for 2 more coats with the hardener. I also just used up all the dye because why not and i rushed the last coat which gave me some runs. Thankfully the runs are under the headrests. The gun pattern wasn't great, very round and would have been better if it was a line. It made it a little tricky to get consistent coverage and I think having done the extra coats probably helped conceal any coverage issues. I contacted them again a few months later so I could get our X5 done (who the f**k thought white leather was a good idea for a family car?!) and they said they had some training to do in Sydney and I could get a reduced rate on the leather fix in the X5 if I let them demo their product on our car. So I agreed. When I took Bec in the E39 to pick it up, I showed them the job I'd done in my car and they were all (students included) really impressed. Note that they said the runs I created could be fixed easily at the time with a brush or an air compressor gun. So, now with the two cars done I can absolutely recommend Colourlock.  I'll take pics of both interiors and create a new thread.
×
×
  • Create New...