Jump to content
SAU Community

Recommended Posts

Hi everyone!

I am new to the forum, and after years of reading the forums thought i would join and start tackling a few jobs on the car. I have a couple questions that I'm sure someone on here could answer!

I had to replace my MAF sensor, the part arrives in a few days. Just wanted to know if i can just reconnect the new MAF and start driving or if i have to do anything else before or after i can use the car again?

And also. I am currently running a K&N filter (the kind you oil) but have read that this sort of filter can be bad for the MAF so am looking at a HKS mushroom filter. Just wanted to know what dimensions for the filter i will need for it to fit in my car (series 2 R33 GTST). To connect it to the MAF etc.

Thanks guys, much appreciated!

Link to comment
https://www.sau.com.au/forums/topic/464774-new-maf-and-air-filter/
Share on other sites

Welcome to SAU dtrants :)

Just put the new maf onto your airbox, plug it in, and start driving.

The maf od is 3" so any 3" pod will fit. But you will need an adaptor. They can be found online or ebay etc.

I used to use a k&n panel filter. I washed it with cold water then let it dry and it was fine for 6 months until I changed my setup. If there are any remnants of oil on the filter and it does make a film over your new maf, get some contact cleaner and spray the maf wire and it should clean it up.

  • Like 1

I actually saw one of those filters fail on Facebook the other day. The nut came off and went straight into the turbo. Plenty of people have used them with no dramas, and it was the first time I have ever seen it happen. So up to you.

I just use the cheap ones from supercheap etc.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Food for thought, the stock oil filter thread is a 3/4-16 UNF, which has an ID of about 10 to 12mm (according to ChatGPT lol). Now compare than to an 10AN, which has an ID of about 14mm (Raceworks is 14.2mm, Speed flow is 14.27mm).  
    • Yep, totally get that. However hooking in for Generator back up is only a few hundred bucks for the wiring. You could put a couple of those in (for different circuits explicitly) and run a couple of baby generators. Bonus, you can balance them across different circuits, and now have backups in your backup. I'm looking at buying places that won't even have water etc, and I don't mind the idea of getting off the electric grid either, even with everything you've said. This country already has enough power outages that even the mains grid isn't that reliable anymore. I do agree though on spending a bit more to get better gear, and to add some extra redundancy in to the system too.
    • You can set hard reserves on your battery system, and it can't be discharged past that.  
    • That sounds like an excellent idea. But total self-sufficiency means exactly that. You have no-one else to blame when your system faults out and you have no power for a week or two while it gets fixed. You'd have to go the whole hog and get a diesel genny and all the switchover gear, to get you through such times. And, despite the fact that over 20 years, my system has been pretty reliable**, I have seen so many inverter explosions (or less dramatic deaths), panel and roof JB fires, and so on, over that time, to know that the stuff is the same as any other bulk Chinese manufactured stuff. The failure rate is well above zero - both on the equipment and on behalf of the meth addled installation labour force. And then..... warranty and means of redress against the supplier you bought the gear from. Best I can tell is that only a handful of solar companies are still around within 5 years of starting their advertising pitch. They disappear and phoenix like crazy. So, as per 1st paragraph, I suspect the only way to is go balls deep and spend maybe 2-3 times as much as you might think, so that you have every base covered. Plus, know and understand your gear intimately, so you can diagnose problems, sort them out yourself, etc, etc. Plus, probably have to consider upgrading various parts as the years pass, to maintain compatibility with newer stuff, performance and reliability, etc, etc. Whereas, remaining attached to the grid has an ongoing cost that keeps going up even if you use bugger all power from it. But it does provide the fallback in case of the worst case with your own gear. You either pay up front or as you go, I suspect.
    • Add more solar panels to the array. Call the electricity company and tell them you're moving out... Live off grid electric wise
×
×
  • Create New...