Jump to content
SAU Community

Recommended Posts

So still in the process of elimination to restore the super smooth idle and engine rev I had pre AMPerformance intake and new 7 range plugs.

Idle is more like a rumble and and rev is a tad rough compared to before, but it bothers me a lot and sucks on long drives.

Also noticed an decline in fuel consumption.

I've changed coils packs for nothing so it's not those.

Could be a bad plug, or maybe just the difference between the factory 6 and iridium 7.

The last thing could be the absence of the resonator on the intake.

I remember Dale retained his and just fabricated a better flowing bottom half.

I'm thinking of mating a factory top half to the AMPerformance intake to see if it fixes this.

Any thoughts ?

cheers

 

Link to comment
https://www.sau.com.au/forums/topic/465740-m35-rough-idle/
Share on other sites

This is what mine is doing and I have the standard type plugs in and still the standard intake. I have checked several times for a vac leak and changed the hoses and all the sensors to no avail. I have now ordered a couple of new coil plug stems to change over as it seems to be a miss on the drivers side bank. It runs fine when I drop it down a gear and have the revs above 3000rpm but misses and hesitates between 2000 and 3000.

Sent from my SM-G900I using SAU Community mobile app


Link to comment
https://www.sau.com.au/forums/topic/465740-m35-rough-idle/#findComment-7756329
Share on other sites

hmm don't think so, no codes for that.

I'llgive the AFM a clean and clean the plug a bit.

The engine just doesn't sound or feel right.

Like the harmonics are out

 

I'll try fitting a resonator to the AMP intake by welding a pipe onto it to connect it

Link to comment
https://www.sau.com.au/forums/topic/465740-m35-rough-idle/#findComment-7757118
Share on other sites

3 hours ago, conan7772 said:

hmm don't think so, no codes for that.

I'llgive the AFM a clean and clean the plug a bit.

The engine just doesn't sound or feel right.

Like the harmonics are out

 

I'll try fitting a resonator to the AMP intake by welding a pipe onto it to connect it

from my experience, i'd say some AFM issue may not trigger the dash CEL.

when you totally blow the AFM, then there is CEL, but for intermittent AFM problem, there may not have CEL

Edited by YangLIU
Link to comment
https://www.sau.com.au/forums/topic/465740-m35-rough-idle/#findComment-7757182
Share on other sites

Given the sealing arrangement used by the AM Performance intake between the two sections; bet my life that the miss is unmetered air getting in through the slip joint.

It's a silly idea, and unless it was an o-rings joint; it will always leak a little, if not a lot.

Link to comment
https://www.sau.com.au/forums/topic/465740-m35-rough-idle/#findComment-7757804
Share on other sites

Given the sealing arrangement used by the AM Performance intake between the two sections; bet my life that the miss is unmetered air getting in through the slip joint.

It's a silly idea, and unless it was an o-rings joint; it will always leak a little, if not a lot.


Never had any issues when i had it on mine....

Air flow is feeling very restricted as of late
  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/465740-m35-rough-idle/#findComment-7757895
Share on other sites

Quote

the smoke test did show leaks in the join, Jez siliconed the two halves together, so should be 99% better.

I'll try the resonator install, easy weld on a piece of pipe , just need a resonator now.

I swear this car went harder before I started modding it, down low anyway.

Might even be a blown head gasket, got oil pissing down on to the turbo now too.

 

 

Edited by conan7772
more info
Link to comment
https://www.sau.com.au/forums/topic/465740-m35-rough-idle/#findComment-7758025
Share on other sites

?/ Don't know mate, I didn't tune it.

Anyway it's not tune related, nor can any tuning fix it.

After fitting new plugs and the intake, which was a mistake, should have only done one then tested, car vibrates on idle and up to around 2500 rpm.

I noticed it instantly and exhaust is louder.

Thought maybe a bad coil.

I've seen a few vids on resonator removal on other cars with massive negative effects.

Strange exhaust tones and loss of power.

Can't find any evidence of improvement.

One article which was quite in depth mentioned intake resonators as crucial to that specific engine design.

Anyway, the engine was way smoother before, so I'm trying hard to restore that.

Apart from that it goes pretty hard, high rpm in low gear manual mode is insane.

If it aint the resonator then I'll try new plugs again, maybe go back to stock 6 spec standard.

If that doesn't fix it I might try drinking way more alcohol.

 

Link to comment
https://www.sau.com.au/forums/topic/465740-m35-rough-idle/#findComment-7758377
Share on other sites

Are you 100% sure that the gasket is in place, and the intake is sealed against the comp cover? The gasket is tricky to get in the right spot; and can swing down on the stud. 

What about the sealing face of the intake itself; definitely flat?

It has the hallmarks of an unmetered air leak.

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/465740-m35-rough-idle/#findComment-7758673
Share on other sites

  • 7 months later...
  • 1 year later...

my car just did the same thing when i was driving it stalled on me and lost power, the after 6 tries of cranking, she started up again, i gave her a couple revs to make sure she was running smooth, then when i started driving halfway to my girl's house the car was lugging again at 60km/h. Any idea if this is similar to your guy's cars problems? Any idea what the problem is?

Edited by Spear17
Link to comment
https://www.sau.com.au/forums/topic/465740-m35-rough-idle/#findComment-7875754
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks for the reply @GTSBoy Haven't really thought of that yet, but you are right. If the hose was damaged it should be absolutely pissing by now. I'll put some heat sleeve around it for good measure since I'm already removing the line anyway.  Maybe I'll put on some of the stock hardlines if I ever fully remove the turbos again. Maybe when T51R modding the compressor housings? Might be a fun mod on GT28s for that "fake single turbo" effect.
    • Update 1: I did some work on the car already before finalizing this post and my "issues" list. I dropped the Tomei exhaust in favor of the HKS Hi Power Silent. Sounds nice and I can actually hear myself think now. Also gives me a realistic chance to legally drive without silencer inserts. A bit of cheating was necessary to still be able to mount the Top Secret style diffuser. Some malusage of washers and a bit of "convincing" toward the brackets and exhaust hanger seemed to do the trick. The shaky steering wheel has been resolved as various suspension components were worn, like sway bar bushings and link bars. Most notably the two steering tie rod ends. Had some trouble finding bushings because my sway bars are not OEM thickness, 23.x up front and 27 rear. But non adjustable, so no aftermarket I suppose. Maybe they are nismo units? Turbo oil drain hoses were definitely still the originals and are new now. Wasn't the cause of the turbo oil leak sadly. Currently removing the rear turbo because of it, I suspect the braided oil feed line is the culprit. This issue needs to be dealt with so I can work towards actually getting the turbo setup legal and inspected. Two new issues to add to the list as well. Rear Main seal is probably leaking. Time will show how bad it is, I don't really want to drop the gearbox right now just for the stupid seal. Could fix a few other things in one go once I do that. Front right driveshaft grease is going past the cv boot, so at some point I'll fix that too.
    • Ok so no 4cyl clutch... Yeah it is a factory manual. So if iam correct i need clutch and flywheel too? I can use something that suits something like R32 GTST?   EDIT: https://www.ebay.com/itm/224291042776 Is this ok?   EDIT2: i maybe forget to mention this(dk how important it is) but the trans will be behind RB25DET NEO(iam doing swap) It will be there for a little while. Iam planing to do bigbox or BMW tranny..
    • You're probably right about that one. Thanks for your suggestions, I hope I don't need a new 3rd brake light. Although wiring issues might arguably be worse. Right now I'm in the midst of a turbo removal because of my oil leak, other problems are going to have to wait for now.
    • Hell, I know that much. So far I just put it off as "part of the deal".
×
×
  • Create New...