Jump to content
SAU Community

Common problems?


Guest tgriffin
 Share

Recommended Posts

Guest tgriffin

Hey guys,

Another newbie question..

What common costs can I expect when I import a '96 R33 GTSt (grade 4) in terms of repairs? Basically, when I get the car, can I expect things to require replacement or fixing?

A couple of things I heard were the radio (frequencies different in Japan), air con (much hotter here!), brake pads/clutch/other durables?

Link to comment
Share on other sites

generally, a lot of stuff will be fixed and replaced during compliance (including new tyres all round).

The air con in both my 180, my surf and my Skyline were all fine, so i have never had to change them.

The FM expander is like $40... you need it unless you like radio stations between 76.0 and 99.9mhz

thats it really... theres not too many hidden costs, most of it is covered during compliance.

Christian

Link to comment
Share on other sites

I would say expect maybe clutch and brake pads. Not always, but people often people will not replace stuff right before they sell.

Other costs to expect... when u get the modding bug!: pod filter, fmic, zorst, turbo etc :D

But in the end, its all worth it !

Link to comment
Share on other sites

usually you have to cover the costs of rego, transportation, and new tyres (usually they're not included in the price of importation) so put aside a couple of grand for that (if you want good tyres n stuff)

Inside the car, you might get air con vents cracked or little bits n pieces showing signs of weather, like the leather on the steering wheel flaking etc (due to age n stress).

If possible during compliance see if you can get them to put the old oil n air filters back in after compliance n rego coz sumtimes you get good catalytic converters, n filters being exchanged with ones that are half as good but comply to australian rules. Theoretically this is illegal, but once rego is done you'll be modding em to bring em up tot the same level anyway.

That's about it, maybe cost for cleaning the car n patching up holes in interior, replacing a few bulb etc, that's about it.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • Hi SAU community  Wondering what my 93 Very RARE TH1 Blue R32 GTR VSpec is worth these days?? Build is fairly dated now All Mods are Compliance Approved  Runs RB26 done only 10000ks Greddy T88 done only 8000ks HKS Cam 1000cc Injectors Full Titanium Exhaust Nismo Intercooler Nismo Oil Cooler HKS Oil sump Tein Super Street Coils Cusco Sway Bars RAYS TE37 19x10.5 DYNO street tune makes around 700hp on 98octane  
    • It does sound like a fuse considering the indicators work..I’ll triple check when I’m free and report back.    thanks for the reply.
    • no, the car was a manual 5 speed from the factory and still is.
    • While going through data logs late last week, I spotted a small issue with my WMI. My WMI starts to progressively inject at 11psi of boost. I'm using a 25psi cut in pressure switch on my WMI as an added safety and if the curve is linear, I should hit that 25psi on my WMI system around 13-14psi of boost.  As per my data logs, my WMI pressure switch only activates around 19psi of boost. This is causing my non WMI 4D map to trim for WMI. I'm presuming this is caused by the mechanical switch response time, injection curve not being linear or both.  I ordered a 2-10psi adjustable cut in pressure switch which should correct this. If this doesn't resolve it before my dyno appointment on Friday, I'll just remove the pressure switch temporarily and more than likely replace it with a pressure transmitter afterwards.    BTW Speedtek has yet to refund me.
    • Yep PETG (Polyethylene terephthalate glycol), my 'go to' plastic, printed to precisely how long I wanted 🙂, about a finger length ha ha. I would usually grind up something but since I've got the printer I thought I might give it a try and it worked beautifully ^_^b So with regards to torque, there's a little bit of science behind the orientation of the print, fill density, fill pattern and number of external perimeters which can increase the strength dramatically, but you still need to work within the constraints of the material and the orientation of the model for sure. I certainly wouldn't be making a breaker bar out of plastic, but this little bugger is very strong for it's size that's for sure.
×
×
  • Create New...