Jump to content
SAU Community

Recommended Posts

EOI Trade - 290kw JZS147 aristo 2JZ for GTR 32/33

Wanting to trade my single turbo JZS147 aristo for a lightly modified R32/R33 gtr in Sydney. Or even sell outright if someone is interested.

Not massively fussed on colour, just a clean body with no rust & light modifications is mainly what I'm after, only wanting a weekend street car for now, as the aristo has been for a few years.

Reason for trade is i have no need for the big 4 door, i miss driving manual as my daily is also an auto, & all my spare bits & pieces are for an RB26, not so good for a 2jz.

 

Quick specs list:
* 1995 S2 in black with leather interior & factory sunroof, factory LSD, cruise control

* Rego valid until September 2017

* shift-kitted auto gearbox with trans cooler & factory converter

* 2JZ with single Garrett GT3582 turbo making 286kw at the wheels on 18psi

* Apexi Super AFC piggyback on standard ECU

Turbosmart eboost street boost controller (set to 15psi low & 18psi high boost)

19" work meisters

Veilside twin 3" exhaust

* adjustable fuel pressure reg with gauge in engine bay

* I'm sure there's a whole lot more I've forgotten here

 

Plenty of work done, this is a quick car even for its weight & size. Traction control is there for a reason. I've had this car for the past 3 years now, had a lot of maintenance & servicing work carried out to bring the car back up to a reliable level:
* radiator replaced approx 12 months ago

* lots of seals replaced as it was leaking oil in a few places (no longer), these include front & rear mains

* turbosmart 40mm external wastegate installed & plumbed back into exhaust - approx 12 months old

* turbosmart bov fully plumbed back - approx 12 months old

* Apexi Super AFC & Turbosmart eboost installed as part of upgrade works roughly 12 months ago

 

Car value is being listed at $13K neg, I have roughly 10K in receipts alone for work carried out in the past 2 years. I can add cash on top for a tidy GTR up to a certain point, or I also have a road bike which I can throw in to increase the value on my side.

Please PM me on here, or msg 0407 896 339 for further info, questions or offers.

Cheers, Chris

12186616_901099323276764_8060803638652363446_o.jpg

20141227_122009.jpg

IMG_20160416_152045.jpg

IMG_20160502_170522.jpg

dyno.png

20160213_183633.jpg

20140307_121314.jpg

also would be interested in RS260 stagea, or possibly even GTR with blown engine

 

throw me some offers, worst i can say is id rather keep this beast

  • 2 weeks later...

BUMP

possibly also keen on an RB25/26 powered cefiro / laurel or R32 GTS-T, maybe even an r33 or r34 for a swap closer to same value

 

throw me some offers & see what catches my attention

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...